SUHNER ABRASIVE ROTOmax 2.0, Technical Document

Page: 35 / 92

2.2.4 s
Afety guArd
If a safety guard is supplied with the hand tool, it is
imperative that the safety guard be used.
2.3 r
Ating dAtA
2.3.1 s
pecificAtions
Voltage 1x230/240V - 50/60Hz, 8.9A
Power Input 2000W
Power Output 1650W
Protection class 1
Type of protection IP45
Overload protection yes
No-load speed 500-13‘000min
-1
Sound pressure level 77dB(A), K=1.5m/s
2
Threaded connection for flexible shafts of type:
DIN 10 M10
NA 4, NA 7, NA 10, NA 12
see catalog
NA 10 DIN 10/G28 STEP 03002613
NA 12 DIN 10 G28 STEP 03002912
2.3.2 v
ibrAtion mesurement vAlues of hAnd tools
BSG 10 Test grinding wheel ø 100x25
Measurement value <2.5m/s
2
/K=1.5m/s
2
Drive 7‘000min
-1
FSM 1:1 Test grinding wheel ø 180x6
Measurement value 4.7m/s
2
/K=1.5m/s
2
Drive 8‘000min
-1
WI 7, WI 10 Test grinding wheel ø 50x6
Measurement value <2.5m/s
2
/K=1.5m/s
2
Drive 15‘000min
-1
WH 12 Test grinding wheel ø 100x25
Measurement value <2.5m/s
2
/K=1.5m/s
2
Drive 10‘000min
-1
FH 12 Test grinding wheel ø 80x10
Measurement value <2.5m/s
2
/K=1.5m/s
2
Drive 12‘000min
-1
FH 10 Test grinding wheel ø 80x10
Measurement value <2.5m/s
2
/K=1.5m/s
2
Drive 15‘000min
-1
FH 7, FH 4 Test grinding wheel ø 25x10
Measurement value <2.5m/s
2
/K=1.5m/s
2
Drive 15‘000min
-1
According to ISO/EN 60745.
The specified vibration value was measured with a
standardised test method and may differ from the
actual operating value. The specified value can be
used for product comparisons or for an introductory as-
sessment of work breaks.
2.4 o
perAting conditions
Temperature range during operation: 0 to +50°C
Relative air humidity: 90% at +30°C, 65% at +50°C
To avoid strong looping movements and beaming
of the flexible shafts, the working pressure must
be reduced.
3.
haNDLINg
/ o
PERaTIoN
3.1 m
Achine
3.1.1 c
ontrol keypAd
Speed gauge (1). Speed correction «-/+» (2). Speed con-
firmation «enter» (3). «run» start command (4). «stop» stop
command (5). ON/OFF «step» safety device (6).
3.1.2 s
tArting the mAchine
Before turning on the machine, make sure to re-
move wrenches and adjusting tools.
When turning on, hold the flexible shaft extended.
During operation make sure that the flexible shafts have
large bend radius.
Before starting the machine, hold the hand tool against
turning!
Operate power switch of the machine.
Speed gauge blinking.
Pre-select speed with key «-/+».
The speed gauge blinks until the pre-selection is con-
firmed with the «enter» key.
The speed is saved.
If a start command is not issued within 60 seconds, the
speed gauge will start to blink.
Now pre-select the speed again by pressing the «enter»
key.
Press the «run» key = Start the machine.
During operation the speed can be varied with the «-/+»
keys.
3.1.3 m
Achine stop
Press «stop» key.
Hold hand tool steady until the speed Zero is reached.
Speed blinks.
35
PT
ES
IT
EN
FR
DE
NL
PL
CZ
FI
SE
CN
EN