background image

11

DEFROST COMPUTING

21

Function: To set type of computation for 
defrost time.

To change Defrost Computing
parameter, press the set key.

0

1

0

Use UP/DOWN keys to set desired 
value. 

0 = Total of real time. 
Example

 

:

 This means that the time 

calculation for defrost frequency will be 
for the total hours the unit has been 
running.

1 - Sum of total compressor operating 
times.

 This means that for time 

calculation, the unit will add the total 
time the compressor has been in an ON 
mode.
It keeps a record of the hours /-1 
Hour incase of a power failure.

Example 

: If Defrost frequency is set to 6 

hrs. and 3 ½ hrs have passed after unit 
has started and power fails, then defrost 
cycle will stat after 3 hours when power
resumes.

12

CRC1200

CRC1200

To change Coil Probe Cal.
parameter, press the set key.

COIL PROBE CAL.

17

Range

Min

Max

Fact. Set 

Range

Min

Max

Fact. Set 

EVAP At DEFROST

18

Function: To set Evap. Fan status during 
defrost.

Use UP/DOWN keys to set desired 
value. 

0 = Evaporator Fan will stay OFF during 
defrost.
1 = Evaporator Fan will stay ON during 
defrost.

To change Evap At Defrost
parameter, press the set key.

0

1

0

Range

Min

Max

Fact. Set 

Range

Min

Max

Fact. Set 

0

1

0

EVAP At DOOR OPEN 

Use UP/DOWN keys to set desired 
value. 

0 = ON
1 = OFF

19

Function : Evap fan status during door
open condition.

To change Evap at Door Open 
parameter, press the set key.

Range

Min

Max

Fact. Set 

Range

Min

Max

Fact. Set 

In time it may be possible that the display 
may  be  offset  by  a  degree  or  so.  To 
compensate for this error, you may need 
to add or minus the degrees required to 
achieve the correct temperature. Setting 

o

o

value is from -10 C to + 10 C

O

-10 C

O

10 C

O

0 C

Function: To set coil probe calibration. 

Use UP/DOWN keys to set desired 
value. 

Sr. 

No.

Parameter setting method

Description of parameters and functions.

Parameter

(LCD Message)

Sr. 

No.

Parameter setting method

Description of parameters and functions.

Parameter

(LCD Message)

DEFROST TYPE

Use UP/DOWN keys to set desired 
value. 

0 = Heater defrost in which case    
      Compressor is OFF.
1 = Hot gas defrost where Compressor     
      is ON.

20

Function : To set type of defrost.

To change Defrost Type
parameter, press the set key.

0

1

0

Range

Min

Max

Fact. Set 

Range

Min

Max

Fact. Set 

DEFROST FREQUENCY

Use UP/DOWN keys to set desired 
value. 

This is the amount of time between two 
defrost cycles.

22

Function: To Set Defrost frequency.

To change Defrost Frequency
parameter, press the set key.

1 Hrs

12 Hrs

4 Hrs

Range

Min

Max

Fact. Set 

Range

Min

Max

Fact. Set 

Range

Min

Max

Fact. Set 

Range

Min

Max

Fact. Set 

Use UP/DOWN keys to set desired value.

This  is  the  maximum  amount  of  time 
allowed for a defrost.  If set to 0, there will 
be no defrost cycle.

To change Defrost Duration
parameter, press the set key.

DEFROST DURATION

23

Function:To  set  Maximum  Defrost 
duration.

Summary of Contents for CRC 1200












Reviews: