background image

The information in this document is

 

subject

 

 to change in order to improve 

reliability,  design  or  function  without  prior  notice  and  does  not  represent

 

commitment on the part of the company. In no

 

event will the company be liable 

for direct, indirect, special, incidental or consequential damage arising out of 
the use or inability to use the product or documentation, even if advised of the 
possibility of such damages. No part of this manual may be reproduced or 
transmitted in any form or by any means without the prior written permission of 
the company.

 Notice

Disclaimer

 Warranty

This manual & its contents remain the sole property of A.S.Controls Pvt.Ltd., 
India and shall not be reproduced or distributed without authorization. Although 
great care has been taken in the preparations of this document, the company 
or its vendors in no event will be liable for direct, indirect, special, incidental or 
consequential damage arising out of the use or inability to use the product or 
documentation, even if advised of the possibility of such damages. No part of 
this manual may be reproduced or transmitted in any form or by any means 
without  the  prior  written  permission  of  the  company.  A.S.Controls  Pvt.Ltd. 
reserves the right to make and changes or improvements without prior notice.

This product is warranted against defects in materials and workmanship for a 
period of one   year from the date of purchase. During the warranty   period, 
product determined by us to be defective in form or function will be repaired or, 
at our option,

 

replaced at no charge. This warranty does not apply if the product 

has been damaged by accident,

 

abuse, and misuse or as a result of service or

 modification other than by the company. This warranty is in lieu of any other 
warranty expressed or implied. In no event shall the company be held liable for 
incidental or consequential damages, such as lost revenue or lost business 
opportunity arising from the purchase of this product.

INDIA

Ball Valves

Globe Valves

Hand Valves

Flow Switches

Solenoid Valves

OUR OTHER PRODUCTS

Cold Room Controller

Chiller Controller

Two Compressors Controller

Heating Controller

Humidity Controller

Pressure Controller

TM

19

CRC1200

03 / 27.08.11

Summary of Contents for CRC 1200












Reviews: