manualshive.com logo in svg

Stuart Turner Monsoon U1.5 bar Twin, Installation Instructions Manual

Share
Download
Stuart Turner Monsoon U1.5 bar Twin Installation Instructions Manual Download Page 18

- 18 -

TECHNICAL SPECIFICATION

Stuart Turner reserve the right to amend the specification in line with its policy of

continuous development of its products.

Note:

For information on other voltages/frequencies which are not shown, consult any
supplementary instruction sheet supplied, or the rating label attached to the 
pump.

*Note:

Max working pressure is the maximum pressure that can be applied to the 
pump internal casing under any installation conditions.

**Note: In normal circumstances the temperature of stored water should never exceed 

65°C.  A stored water temperature of 60°C is considered sufficient to meet all 
normal requirements and will minimize deposition of scale in hard water areas.

Maximum permissible water temperature 65°C.

Model

U1.5 bar

Twin

U2.0 bar

Twin

U3.0 bar

Twin

U4.0 bar

Twin

U4.5 bar

Twin

Electrical

Power supply
Volts/phase frequency

Motor enclosure

Type of motor

Max. power consumption

Full load current

Rating

Max. no. starts per hour

230/1/50

IPX4

Induction

355 Watts

1.5 Amps

Continuous
(S1) @ 9 l/min
& above 
(Both ends
pumping)

60

230/1/50

IPX4

Induction

435 Watts

1.9 Amps

Continuous
(S1) @ 9 l/min
& above 
(Both ends
pumping)

60

230/1/50

IPX4

Induction

655 Watts

2.9 Amps

Continuous
(S1) @ 9 l/min
& above 
(Both ends
pumping)

60

230/1/50

IPX4

Induction

875 Watts

3.9 Amps

Continuous
(S1) @ 9 l/min
& above 
(Both ends
pumping)

60

230/1/50

IPX4

Induction

1135 Watts

5.1 Amps

Continuous
(S1) @ 9 l/min
& above 
(Both ends
pumping)

60

Mechanical

Max inlet head

Max head (closed valve)

Max working pressure*

Max ambient air temperature

Pressure vessel air pre-charge

Max water temperature**

Min water temperature

8 metres

15 metres

600 kPa 
(6.0 bar)

40°C

90 kPa (0.9
bar) (13 psi)

65°C

4°C

8 metres

20 metres

600 kPa 
(6.0 bar)

40°C

90 kPa (0.9
bar) (13 psi)

65°C

4°C

8 metres

30 metres

600 kPa 
(6.0 bar)

40°C

90 kPa (0.9
bar) (13 psi)

65°C

4°C

12 metres

40 metres

600 kPa 
(6.0 bar)

40°C

130 kPa (1.3
bar) (18.5 psi)

65°C

4°C

12 metres

45 metres

600 kPa 
(6.0 bar)

40°C

130 kPa (1.3
bar) (18.5 psi)

65°C

4°C

Dimensions

Length

Width

Height (excluding flexible hoses)

Gross weight (packed)

265 mm

162 mm

243 mm

9.2 Kg

265 mm

162 mm

243 mm

9.2 Kg

265 mm

162 mm

243 mm

10.4 Kg

300 mm

162 mm

243 mm

12.5 Kg

310 mm

162 mm

243 mm

13.3 Kg

Summary of Contents for Monsoon U1.5 bar Twin

























Reviews:

No comments

Brands by name

Popular brands

Load more brands