Stuart Turner Flomate Mains Boost 46574 Installation & Maintenance Instructions Manual Download Page 2

- 2 -

Cont ...

PRODUCT DESCRIPTION

Electric motor driven peripheral pump with bypass, complete with an automatic control 
system consisting of flow switch and electronic control.

APPLICATION

The Flomate is a mains booster pump with an automatic control system for domestic 
use, designed to assist the pressure from the mains supply, where the mains pressure is 
insufficient.  This unit requires a minimum unassisted supply flow of 0.6 l/min to operate.
The pump is limited to producing a maximum flow of not greater than 12 l/min, and a 
maximum pressure of 3.0 bar.
When the flow/pressure from the rising main exceeds the pump output, the 

patented 

applied for integral bypass will direct the water into the system as normal.

The Flomate mains booster is a patent granted design.

Please note the following warning signs.

Warning of possible electrical hazard.

 

Possible danger to personnel or important installation requirement.

 

All the safety and operating instructions in this booklet must be  

 

 followed. 

 

The pump must not be used for any other application without the    

 

written consent of Stuart Turner Limited.

 

The pump must be installed by a qualified person.

 

The pump is not suitable for heavy commercial/industrial    

 

 applications.

 

The installation must comply with the latest Building Regulations,   

 

Wiring Regulations (BS 7671) and Water Supply Regulations (see    

 notes).

 

This appliance can be used by children aged from 8 years and  

 

 

above and persons with reduced physical, sensory or mental  

 

 

capabilities or lack of experience and knowledge if they have been  

 

given supervision or instruction concerning use of the appliance    

 

in a safe way and understand the hazards involved.  Children shall   

 

not play with the appliance.  Cleaning and user maintenance shall   

 

not be made by children without supervision.

 

Children should be supervised to ensure that they do not play with  

 the 

appliance.

Notes

 

This product must be installed in accordance with the current  

 

 

Water Supply (Water Fittings) Regulations.

 

Under no account should the internal flow restrictor be removed,    

 

or replaced with an alternative design.

Summary of Contents for Flomate Mains Boost 46574

















Reviews: