Stuart Turner Flomate Mains Boost 46574 Installation & Maintenance Instructions Manual Download Page 14

- 14 -

Cont ...

8  THE FLOMATE GUARANTEE

Congratulations on purchasing a Stuart Turner pump. 

We are confident this pump will provide many years of trouble free service as all our    
products are manufactured to the very highest standard. 

The Flomate Pump is guaranteed to be free from defects in materials or workmanship  
for 3 years from the date of purchase.  

Within the guarantee period we will repair, free of charge, any defects in the pump  
resulting from faults in material or workmanship, repairing or exchanging the whole 
unit as we may reasonably decide. 

Not covered by this guarantee: Damage arising from incorrect installation, improper    
use, unauthorised repair, normal wear and tear and defects which have a negligible    
effect on the value or operation of the pump. 

Reasonable evidence must be supplied that the product has been purchased within    
the guarantee term prior to the date of claim (such as proof of purchase or the pump    
serial number). 

This guarantee is in addition to your statutory rights as a consumer.  If you are in any  
doubt as to these rights, please contact your local Trading Standards Department. 

In the event of a claim isolate the unit and then please telephone 

‘PumpAssist’

.

+44 (0) 844 98 000 97

 Proof of purchase should accompany the returned unit to avoid delay in investigation  
and dealing with your claim. 

You should obtain appropriate insurance cover for any loss or damage which is not    
covered by Stuart Turner Ltd in this provision.

Please record here for your records.

TYPE NO.

SERIAL NO.

DATE PURCHASED

Summary of Contents for Flomate Mains Boost 46574

















Reviews: