Stuart Turner CH4-30 Installation, Operation & Maintenance Installation, Operation & Maintenance Instructions Download Page 9

- 9 -

5  TECHNICAL SPECIFICATION

Stuart Turner reserve the right to amend the specification in line with its policy of 
continuous development of its products.

 

*Note:  The maximum pressure that can be applied to the pump under any  

 

 

 

installation conditions.

 

**Note:  A stored water temperature of 60

o

C is considered sufficient to meet all    

 

 

normal requirements and will minimise deposition of scale in hard water  

  

areas.

 

*** With footvalve fitted.

 

Although these pumps are self priming we recommend a footvalve/strainer is    

 

used if a suction lift is required.

5.11 

Noise:

  The equivalent continuous A-weighted sound pressure level at a  

 

 

distance of 1 metre from the pump does not exceed 70 dB(A).

Pump Model

CH4-30

50 Hz

46553

CH4-40

50 Hz

46554

CH4-50

50 Hz

46555

CH4-60

50 Hz

46556

General

Guarantee

2 years

WRAS approval

1601035

Features

Pump type

Centrifugal

Mechanical seal

EPDM / Carbon / Ceramic

Materials

Pump body

Brass / stainless steel

Impeller

Stainless steel

Performance

Maximum head (closed valve)

25 metres

36 metres

50 metres

62 metres

Performance @ 50 l/min

22 metres

34 metres

46 metres

56 metres

Performance @ 100 l/min

13 metres

22 metres

34 metres

44 metres

Maximum flow

140 l/min

160 l/min

Minimum static inlet pressure

0.05 bar (0.5 metres)

Maximum static inlet pressure

1.0 bar (10 metres)

Maximum working pressure*

600 kPa (6 bar)

900 kPa (9 bar)

Max. ambient air temperature (Continuous)

40 

o

C

Max. ambient air temperature (Intermittent)

50 

o

C

Min / Max water temperature**

Min 4 

o

C / Max 65 

o

C

Maximum Suction Lift***

5 metres

Connections

Pump connections

G 1¼ female (inlet), G1 female (outlet)

Motor

Type

Induction, auto-reset thermal trip

Duty rating

Continuous (S1)

Electrical

Power supply / phase / frequency

230 V a.c. / 1 / 50 Hz

Current (full load)

3.8 Amps

5.3 Amps

7.4 Amps

8.8 Amps

Power consumption

850 Watts

1182 Watts

1648 Watts

1969 Watts

Fuse rating

13 Amps

Power cable (pre-wired)

0.75 metres

Physical

Enclosure protection

IPX5

Length

360 mm

384 mm

431 mm

456 mm

Width

155 mm

187 mm

Height (excluding hoses)

190 mm

210 mm

Weight (including fittings)

11.1 Kg

11.6 Kg

16.8 Kg

19.3 Kg

Summary of Contents for CH4-30













Reviews: