IIsso
oA
Aiirr®
® ssu
up
pp
po
orrtt ssu
urrffa
acce
e rre
ep
plla
acce
em
me
en
ntt kkiitt iin
nssttrru
uccttiio
on
nss
If you ordered Model 2941 IIsso
oA
Aiirr System, disregard these instructions and refer to the Model 2941 IIsso
oA
Aiirr System
Operations Manual.
Use these instructions if you are replacing Model 2940 IIsso
oA
Aiirr support surface with Model 2941-001-100 IIsso
oA
Aiirr support
surface.
T
To
oo
ollss rre
eq
qu
uiirre
ed
d
•
None
P
Prro
occe
ed
du
urre
e
1. Loosen the tie down straps that secure the 2940 support surface to the bed frame.
2. Remove and discard the 2940 support surface.
3. Unpack the 2941-001-100 support surface and discard the packaging.
4. Setup the 2941-001-100 support surface follow the Model 2940 AO-SM-70-INT Operations Manual.
N
No
otte
e
•
For instructions about how to use the Model 2941 IIsso
oA
Aiirr Support Surface with the Model 2940 IIsso
oA
Aiirr Pump, see the
AO-SM-70-INT Operations Manual. The content in this instruction sheet is a supplement to your Model 2940 IIsso
oA
Aiirr
Operations Manual.
•
Do not service the 2941-001-100 support surface with the Model 2940 Operations/Maintenance/Service Manuals.
•
Do not launder the 2941-001-100 support surface.
•
Use this instruction sheet for cleaning and disinfecting instructions of your 2941-001-100 support surface.
•
To view your Operations or Maintenance Manual online, see https://techweb.stryker.com/.
For available service parts, contact Stryker Customer Service or Technical Support at: 1-800-327-0770.
S
Su
um
mm
ma
arryy o
off ssa
affe
ettyy p
prre
ecca
au
uttiio
on
nss
Always read and strictly follow the warnings and cautions listed on this page. Service only by qualified personnel.
W
WA
AR
RN
NIIN
NG
G
•
Always check the CPR connector before use. Replace if visibly soiled. Direct skin contact with soiled material may
increase the risk of infection.
•
Always inflate the product and unplug the pump from the mains before you clean or disinfect.
•
Do not immerse the product in cleaning or disinfectant solutions.
•
Always make sure that you wipe each product with clean water and dry each product after cleaning or disinfecting. Some
cleaning and disinfecting agents are corrosive in nature and may cause damage to the product if you use them
improperly. If you do not rinse and dry the product, a corrosive residue may be left on the surface of the product that
could cause premature degradation of critical components. Failure to follow these cleaning or disinfecting instructions
may void your warranty.
•
Do not allow fluid to pool on the support surface. Fluids may cause premature degradation of components and may
cause unpredictable safety and performance of this product.
•
Always disinfect the support surface between patients, to avoid the risk of cross-contamination and infection.
C
CA
AU
UT
TIIO
ON
N
•
Improper usage of the product can cause injury to the patient or operator. Operate the product only as described in this
instruction sheet.
•
Do not modify the product or any components of the product. Modifying the product can cause unpredictable operation
resulting in injury to patient or operator. Modifying the product also voids its warranty.
•
Do not tie the support surface to the bed frame with the bottom center D-ring straps to avoid the risk of equipment
damage. The bottom center-D ring straps are for storage only.
•
Always completely dry the support surface covers before storing, adding linens, or placing a patient on the surface.
2941-009-020 Rev E.0
1
EN
