background image

Chapter 1: 

The Sunflower Operations Manual

 

 

1.  INTRODUCTION 

This Operations manual is designed to assist you with the operation of the Sunflower bed. 
Before operating the bed, it is important to thoroughly read and understand all information in this 
manual.  
Hospital staff should be able to refer to this manual at all time when using the bed. A 
Maintenance manual, included in the Customer’s Guide, is also available to assist you with the 
servicing of the bed. 
This Operations manual is an integral part of the bed and should be turned over to the new user 
should the bed be sold or transferred.

 

1.1  BED SPECIFICATIONS * 

Load Capacity 

450 lb (204 kg) 

Fowler Angle 

0° to 85° 

Knee Gatch Angle 

0° to 30° 

Sleep surface  

36" x 76" - 78-1/2" (91.5cm x 193 cm - 199 cm) 
Accommodates 35" x 76" - 78" - 80" (89 cm x 193 cm - 
198 cm - 203 cm) mattresses. 

Minimum/Maximum Bed Height 
-FL18E1/M1 
-FL18E2/M2 

 
11 to 25 in. (28 to 63.5 cm) 
12 to 26 in. (30.5 to 66 cm) 

Bed Stabilizing System 
-FL18E1/M1 
-FL18E2/M2 

 
Reverse Lock System (Bed Normally Rests on Legs) 
Floor Lock System (Bed Normally Rests on Casters) 

Overall Weight: 
-FL18E1/E2 Fully Electric w/Full-Length 

Siderail and Designer Boards. 

-FL18M1/M2 w/Full-Length Siderail and 

Designer Boards. 

 
 
288 lb (127 kg) 
 
260 lb (118 kg) 

Overall Dimensions 
-Length: 76" Bed w/o and w/Bumpers 
             80" Bed w/o and w/Bumpers 
-Width: Siderail down - Siderail up  

 
84 1/8 in. - 86 1/4 in. (214 cm - 219 cm) 
86 5/8 in. - 89 in. (220 cm - 226 cm) 
39 1/4 in. - 42 in. (99.6 cm - 106.6 cm) 

Electrical Requirements - All electrical 
requirements meet the CSA standard C22.2 
No. 125 and UL 544 specifications for class 
2G. 

120 V, 50/60 Hz, 5 A 
 

* Stryker Bertec Medical Inc provides special attention to product improvement and reserves the right to change 
specifications without notice. 

1.2  TECHNICAL SUPPORT

 

For questions regarding this product, please contact one of the following Technical Service 
departments or your local representative:

 

In Canada: 

In the United States:

 

Stryker Bertec Medical Inc 

Stryker Medical 

 

Service in English: 1 800 428-5025  

1 800 327-0770 

Service in French: 1 800 361-2040 

6300, Sprinkle Road 

E-mail: 

[email protected]

 

Kalamazoo, MI 49001-9799  

70, 5

th

 Avenue, P.O. Box 128 

USA 

L’Islet (Quebec), G0R 2C0, Canada 

 

Summary of Contents for BERTEC SUNFLOWER FL18E1
















Reviews: