background image

TABLE OF CONTENTS 

N

N

O

O

T

T

E

E

 

 

Stryker Bertec Medical Inc gives special attention to the quality of the information found in this document. 
Any comments on its content will be most welcomed. Please forward your remarks to the Technical 
Service department (see section 1.2).

 

 

1.  INTRODUCTION...................................................................................................................................... 4

 

1.1  BED SPECIFICATIONS ................................................................................................................... 4

 

1.2  TECHNICAL SUPPORT ................................................................................................................... 4

 

1.3  WARNING / CAUTION / NOTE DEFINITIONS ................................................................................ 5

 

1.4  SAFETY PRECAUTIONS ................................................................................................................. 5

 

1.5  WARRANTY ..................................................................................................................................... 7

 

Limited Warranty ............................................................................................................ 7

 

To Obtain Service and/or Parts....................................................................................... 7

 

Return Authorization....................................................................................................... 7

 

Damaged Merchandise .................................................................................................. 7

 

1.6  BED CLEANING AND MATTRESS CARE....................................................................................... 7

 

Cleaning Beds ................................................................................................................ 8

 

Mattress Care................................................................................................................. 8

 

1.7  SET-UP PROCEDURES .................................................................................................................. 8

 

Electric (FL18E1/E2) Bed Checklist................................................................................ 8

 

Manual (FL18M1/M2) Bed Checklist............................................................................... 9

 

1.8  BED ILLUSTRATION........................................................................................................................ 9

 

2.  BED OPERATION GUIDE..................................................................................................................... 11

 

2.1  POSITIONING THE BED THROUGH: ........................................................................................... 11

 

The Foot End Control Panel ..........................................................................................11

 

The Removable Pendant Control...................................................................................12

 

The Hand Cranks ..........................................................................................................12

 

2.2  MOVING OR STABILIZING THE BED (ELECTRIC AND MANUAL BEDS) .................................. 13

 

Reverse Lock system (FL18E1 and FL18M1 Bed Models) ............................................13

 

Floor Lock System (FL18E2 and FL18M2 Bed Models).................................................14

 

2.3  POSITIONING SIDE-RAILS ........................................................................................................... 14

 

Raising a Side-Rail ........................................................................................................14

 

Lowering a side-rail .......................................................................................................14

 

2.4  HEAD AND FOOT BOARDS .......................................................................................................... 15

 

Removing Boards..........................................................................................................15

 

Replacing Boards ..........................................................................................................15

 

2.5  PATIENT RESTRAINT STRAP LOCATIONS ................................................................................ 15

 

2.6  FOOT SECTION SUPPORT ROD (OPTIONAL)............................................................................ 15

 

Vascular Positioning ......................................................................................................15

 

Trendelenburg Position .................................................................................................15

 

2.7  EMERGENCY CRANK (OPTIONAL) ............................................................................................. 15

 

Operating the Emergency Crank ...................................................................................15

 

Storage..........................................................................................................................15

 

 

Summary of Contents for BERTEC SUNFLOWER FL18E1
















Reviews: