manualshive.com logo in svg

Stryker Medical COMPANION, Operation And Maintenance Manual

Share
Download
Stryker Medical COMPANION Operation And Maintenance Manual Download Page 21

20

Assembly Instructions

Assembly part numbers
3100-100-1 11 (Single Top Table with T-Band)
3100-100-151  (Single  Top Table with Edgemold)

NOTE
Lift/Lower Handle adjustment is properly set at the factory.  Do not adjust the locking nut prior to assembly
of product.

ASSEMBLY METHOD

1.1  Lift item E (cover) off the base frame.

1.2  Insert the bottom plate of item K (column assembly) through the opening in item E (cover) as shown.

1.3  Attach item K (column) to the base frame, as shown, using a 3/16“ Allen wrench and (3) item B

(truss head torx screws).

1.4  Attach item C (clip nut) through the square opening in item F (base weldment).

1.5  Push the bottom flange of the bellows through the opening in item E (cover).

1.6  Place item E (cover) over the base.

1.7  Attach item E (cover) using (8) item D (truss head screws).

1.8  Attach item G (top assembly) to item K (column assembly) using a 3/16” Allen wrench and (6) item A

(socket head cap screws).

Summary of Contents for COMPANION





























Reviews:

No comments

Brands by name

Popular brands

Load more brands