background image

GENERAL CLEANING (TO BE PERFORMED BY STORE PERSONNEL) 

23 

FREQ. 

AREA / INSTRUCTIONS 

Daily 

Acrylic Air Deflectors (See Illustration Below):  



Use 

WASH

 spray bottle on air deflectors. Wipe off residue with paper towel. 



Use 

RINSE

 spray bottle on air deflectors. Dry with paper towel. 

Weekly  Decks (See Illustration Below):  



Remove product from case.  



Use 

WASH

 spray bottle on decks. Wipe with paper towel.  



Use 

RINSE

 spray bottle on decks. Dry with paper towel.  



Use 

SANITIZE

 spray bottle on decks. Let air dry. 



For stubborn stains/residue, remove product from case. TURN MAIN POWER SWITCH OFF.  Remove 
decks from case.  Submerse in warm, soapy water solution in back room pot sink. Use spray nozzle on 
pot sink or use 

RINSE

 spray bottle on decks. Dry with paper towel. Return decks to case.  



Return product to case. Turn main power switch back on. 

Weekly  Shelving/Brackets/Optional Tag Molding (See Illustration Below): 



Remove product from case.  



Use 

WASH

 spray bottle to spray components. Wipe with paper towel. 



Use 

RINSE

 spray bottle on components. Dry with paper towel.  



Use 

SANITIZE

 spray bottle on shelving, brackets and molding.  



Let air dry. Return product to case. 

Weekly  Exterior Surfaces (Header/Rear Plenum/ Front Panel/Lower Panel/Stainless Mirror). See Illustration Below:  



Use 

WASH

 spray bottle on exterior surfaces. Wipe with paper towel. 



Use 

RINSE

 spray bottle on exterior surfaces. Dry with paper towel. 

Weekly  Removable, Magnetized Condenser Coil Filter: See next page. 

Monthly  Condenser Coil:  



See next page for lower panel removal and location of condenser coil. 



If using vacuum, use brush attachment to thoroughly clean entire coil. 



If using brush, both metal or fiber brush may be used to remove dust and dirt that can collect on        
condenser coils. Avoid damaging fins on condenser coil. Replace lower panel.   

Monthly  Under Case Cleaning: Remove lower panels. Vacuum under case to remove all dust, dirt and debris.       

Replace lower panels. 

Daily 

Stainless Steel Mirrors: Use stainless steel cleaner or glass cleaner on surface to remove finger prints and 
smudges. Wipe with paper towel. 

Summary of Contents for FSE663R





































Reviews: