background image

22 

CLEANING SCHEDULE 

R

888 Porter Rd.  Muskegon, MI  49441  Phone: 231.798.8888  Fax: 231.798.4960  www.structuralconcepts.com 

 

Cleaning 

 

Daily 

 

Weekly 

 

Monthly 

 

Task 

Clean Case Exterior 

 

 

Clean outside surface of front curved glass 
with a household or commercial glass 
cleaner. 

 

 

 

Clean wood, laminate and painted surfaces 
with a mild soap and water solution and a 
soft cloth .  

 

 

 

Remove rear panel. Clean under case with 
vacuum.  

Clean Case Interior 

 

 

Shelves may be cleaned with a household 
or commercial glass cleaner. 

 

 

 

Remove the decks and clean with soap and 
water. 

 

 

 

Remove rear doors and clean with a house-
hold or commercial cleaner  

 

 

 

Vacuum tub under deck if necessary.  To 
flush out the tub, disconnect power to the 
case.  Remove the deck and the fan 
shroud.  Direct drain to floor drain or a 
bucket.  Run hose into the drain to flush out 
debris.  Hose out the tub. 

 

 

 

Keep drains clean and free of debris which 
could clog the drain and rob the case of 
needed refrigeration. 

 

 

 

Using air pressure if available, or an indus-
trial strength vacuum, clean the dust and 
dirt that collects on the condenser coil.  (Be 
careful not to damage the fins on the coil.) 

 

 

 

Slide out Refrigeration Unit and use a vac-
uum with a hose attachment to clean area.   

 

 

 

 

 

Summary of Contents for DO3623R




























Reviews: