background image

en

13

User manual INNOVA

www.igloo.pl

Contents

List of Figures

1. UNLOADING 

13

2. PROPERTIES OF THE DEVICE 

13

2.1. Purpose 

13

2.2. Description of the device 

13

2.3. Technical data 

15

3. PREPARING THE DEVICE FOR EXPLOITATION 

16

3.1. Requirements concerning the place of installation 

16

3.2. Connection and actuation 

16

4. EXPLOITATION 

16

4.1. Temperature regulation 

17

4.2. Temperature regulation 

17

5. MAINTENANCE 

17

5.1. Cleaning and maintenance 

17

6. SERVICE 

19

6.1. Fault identification and repair 

19

6.2. Service 

20

7. THERMOSTAT SERVICE 

20

7.1. „IGLOO” thermostat 

20

7.2. „CAREL” thermostat 

21

1. UNLOADING

The device should be transported in vertical position, and it should be properly secured and packed. The manufacturer 

ships the device on a special wooden platform, secured with cardboard angle sections and foil. 

2. PROPERTIES OF THE DEVICE

2.1. Purpose

The „INNOVA” display case is a universal cooling device for displaying and storage of short-term confectionery: tarts, ca-

kes, biscuits, desserts, etc. at temperatures b2°C / +15°C with ambient tempe16°C / +25°C and relative 

air humidity of up to 60%.

2.2. Description of the device

„INNOVA” is equipped in dynamic cooling, automatic condensation evaporation and defrosting. The display case is also 

equipped with an electronic thermostat, which works optionally with the temperature registration module that enables 

registration and signalling high and low temperatures in the unit. Display cases are adapted to connect in sequences and 

can be powered by an internal unit within the temperature range of +2°C / +15°C. It  is possible to control the humidity 

of the display case ranging from 40 to 90%. The exhibition part of the display case are glass shelves placed on a rack.  

The exposition shelves are able to change the position and angle of suspension. The glass elements are made of insu-

lating glass filled with argon and black silk-screen printing.

 

The „INNOVA” display cases use energy-saving LED back 

lighting. „IGLOO” Units are made in accordance with modern technology and possess the certificates required by law.

This sign signifies information of particular meaning for user security and for proper device 

exploitation.

Instruction manual

INNOVA

en

Fig.1 Section of the device 

14 

Fig.2 Control panel 

14

Fig.3 Construction of the unit 

15

Fig.4 Humidistat 

17

Fig.6 Cleaning the condenser 

18

Fig.12 Data plate 

19

Fig.13 „Igloo” thermostat control panel 

20

Fig.14 „Carel” thermostat control panel 

21

List of tables

Table 1 Technical data 

2

Summary of Contents for INN100.110












Reviews: