background image

-3-

T-C-CCN64AU17 © 2017 Simpson Strong-T

ie Company Inc.

Image

Model Number

Dimensions

Description

Finish

Box 

Qty

Collated Strong-Drive

®

 

SCNR RING-SHANK CONNECTOR

 Nail

T9A150MCN

All 

Sizes

40 mm x 3.75 mm

Full round-smooth head, 

Annular-Ring Shank, 

Diamond point

33° – 22 nails per  

paper-collated strips

316 

Stainless 

Steel

1,500

T10A150MCN

40 mm x 3.32mm

1,500

Collated Strong-Drive

®

 

SCN SMOOTH-SHANK CONNECTOR

 Nail

N10HDGPT500

40 mm x 3.75 mm

Full round-smooth head, 

Smooth Shank, 

Diamond point

33° – 22 nails per  

paper-collated strips

Hot-dip 

Galvanised

500

N10HDGPT3000

3,000

N8HDGPT500

40 mm x 3.32 mm

500

N8HDGPT4000

4,000

Need loose connector fasteners?

Visit your local Simpson Strong-Tie website to see our full range.

TOOL & FASTENER SPECIFICATIONS

Model Number

: CCN64 

Action:

 Multi-Blow 

Dims:

 

L305 x W119 x H273 mm 

Weight:

 

2.1 kg 

Operating pressure

:  6.2 – 8.3 bar (90 – 120 psi) 

Magazine:

 

Single strip (approx. 28 nails) 

Angle:

 

33° – 35° 

Collation:

 

Paper tape 

Head:

 

Full round head 

Diameter:

 3.3 

| 3.8 | 4.1 mm 

Length:

 

38 mm | 65 mm (± 2 mm)

This tool uses 3/8 inch N.P.T. male fitting. 

The fitting must relieve 

air pressure when disconnected from the air supply.

TOOL AIR FITTINGS

Summary of Contents for CCN64












Reviews: