background image

Mk6 Theme Plus (Concentric valve) Issue 1.2 21/05/02

 Page 3 of 14

Additional notes for car ports and other single storey 'add-on' extensions

1.  Any carport or other add-on extension should consist of a roof, or a roof and one other

wall. If it consists of a roof and two other walls, the installation shall be treated as
suspect and further advice sought.

2.  If there is any opening in the carport into the dwelling, e.g. door, window, etc., then the

terminal must be at least 1200mm away from that opening. If it is less then the
installation must be treated as suspect and further advice sought. If it is more than
1200mm then D, F, H and I shall also apply where D is the vertical distance between
the lowest point of the roof and the top of the terminal.

3.  If the roof is plastic then the installation should be treated with great care as there is

no simple way of protecting the roof.

Clearances

Soft furnishings, decorations and some wall coverings may discolour or scorch if positioned too
close to the fire.
If a shelf is to be fitted above the fire, perhaps as part of a surround, it must be positioned a
minimum of 1m (39in.) above the top of the hearth, and project no more than 200mm (8in.) from
the front plane of the opening. Combustible material such as wood may be fitted to within
100mm (4in.) of either side of the opening so long as it projects no more than 100mm (4in.) from
the front plane of the opening.

Items supplied

The following items will be found within the fire carton:

1.  Convection box and wall box.
2.  Separate flat trim, optional canopy trim, or spacer frame with box trim depending on

options ordered.

3. Optional 

fret.

4.  2 shaped ceramic fibre blocks plus 2 piece front coals
5.  6 large and 4 small coals.
6.  Screws and wall plugs to complete the installation.
7.  These installation instructions, guarantee card and end user operating instructions.

The following items will be found within the Turboflue carton:

1.  Fan unit with wall plate, pre-wired with connecting cables.
2. Burner 

unit.

3. Connecting 

duct

4.  Galvanised wire to form moisture drip collar.
5.  Switch plate and plaster depth box.
6. Fasteners.
7. Plastic 

cable 

conduit.

8. Insulating 

slab.

Warning: 

 Only Straxgas approved ceramic blocks and coals, designed for this appliance, must

be used with this burner.  Use of ceramic components from any other supplier will invalidate the
guarantee and may be dangerous.
When unpacking the appliance, avoid touching the visible, painted parts as the paint requires
curing (this will take approximately 2 hours under fire. In some cases there may be a slight
odour given off for a short period).

Fret options

The following Straxgas frets are suitable for use with this appliance:

1.  Black Classic / Silver Classic
2.  Black Finger / Brass Finger
3. Delta

NO OTHER FRONTS SHOULD BE USED WITH THIS APPLIANCE

Summary of Contents for FLAIRE WITH TURBOFLUE















Reviews: