installation instructions - electric products
Fitting the splashback (if applicable)
Loosely fit screw A and nut B into hole
1 at both ends of the rear surface of
the appliance.
Locate fitted screw A through the slots
in both of themetal splashback plates.
Tighten screw A and nut B.
Now locate and tighten screw C and
nut D through hole (2) at both ends
of the rear surface of the appliance.
Make sure that the splashback is
securely attached, but avoid over
tightening.
Fitting the towel rail (if applicable)
On the towel rail there are two hole,
top (A) and bottom (B), these holes
have corresponding holes on the
fascia at each end.
The screw for the top hole (A), must
be screwed into the supplied adaptor,
where as the remaining screw just
goes through the bottom hole (B).
Both screws are M6 screws. Using
the allen key provided, tighten the
screws making sure that the towel
rail is flush to the fascia, but not over
tightened.
•
•
•
•
•
•
Installing Your Cooker
Fitting the plinth (if applicable)
�
Make sure the appliance is raised to a height of 915mm
or above before beginning. If the appliance is below
915mm - you can only fit the plinth cover labelled Y.
You can adjust the height using the feet (1) of the
appliance.
If your appliance has a storage drawer at the bottom,
you access the required holes through the base of the
drawer after lifting the mat.
�
Open the appliance doors, and loosen screw A located
on bracket (2). Do not remove this screw entirely.
�
Insert screw B, through slot (3) and screw into the small
hole at the bottom of bracket (2).
Make sure that the plinth cover is flush to the appliance,
but not over tightened.
Fitting the splashback (if applicable)
�
Loosely fit screw A and nut B into hole 1 at both ends of
the rear surface of the appliance.
�
Locate fitted screw A through the slots in both of the
metal splashback plates.
�
Tighten screw A and nut B.
�
Now locate and tighten screw C and nut D through hole
(2) at both ends of the rear surface of the appliance.
Make sure that the splashback is securely attached, but
avoid over tightening.
Fitting the towel rail (if applicable)
�
On the towel rail there are two hole, top (A) and bottom
(B), these holes have corresponding holes on the fascia
at each end.
�
The screw for the top hole (A), must be screwed into
the supplied adaptor, whereas the remaining screw just
goes through the bottom hole (B). Both screws are M6
screws. Using the allen key provided, tighten the screws
making sure that the towel rail is flush to the fascia,
but not over tightened.
�
�
���
���
���
�
�
Door
Plinth cover
Oven cavity
�
���
�
�
�
���
�
�
49
Installing Your Cooker
Fitting the plinth (if applicable)
�
Make sure the appliance is raised to a height of 915mm
or above before beginning. If the appliance is below
915mm - you can only fit the plinth cover labelled Y.
You can adjust the height using the feet (1) of the
appliance.
If your appliance has a storage drawer at the bottom,
you access the required holes through the base of the
drawer after lifting the mat.
�
Open the appliance doors, and loosen screw A located
on bracket (2). Do not remove this screw entirely.
�
Insert screw B, through slot (3) and screw into the small
hole at the bottom of bracket (2).
Make sure that the plinth cover is flush to the appliance,
but not over tightened.
Fitting the splashback (if applicable)
�
Loosely fit screw A and nut B into hole 1 at both ends of
the rear surface of the appliance.
�
Locate fitted screw A through the slots in both of the
metal splashback plates.
�
Tighten screw A and nut B.
�
Now locate and tighten screw C and nut D through hole
(2) at both ends of the rear surface of the appliance.
Make sure that the splashback is securely attached, but
avoid over tightening.
Fitting the towel rail (if applicable)
�
On the towel rail there are two hole, top (A) and bottom
(B), these holes have corresponding holes on the fascia
at each end.
�
The screw for the top hole (A), must be screwed into
the supplied adaptor, whereas the remaining screw just
goes through the bottom hole (B). Both screws are M6
screws. Using the allen key provided, tighten the screws
making sure that the towel rail is flush to the fascia,
but not over tightened.
�
�
���
���
���
�
�
Door
Plinth cover
Oven cavity
�
���
�
�
�
���
�
�
49
Summary of Contents for Sterling R1100E
Page 1: ...User and Installation Instructions Stoves Range Electric...
Page 46: ......
Page 47: ......
