background image

Important Safety Advice

When using electrical appliances, basic precautions
should be followed to reduce the risk of fire, electric
shock, and injury to persons, including the following:

If the appliance is damaged, check immediately with the
supplier before installation and operation.

Do not use this heater in the immediate surroundings
of a bath, shower or swimming pool

.

Do not use outdoors.

This heater must not be located immediately above or
below a fixed socket outlet or connection box.

Do not cover or obstruct in any way the heat outlet grille
located underneath the heater. Overheating will result if
the heater is accidentally covered.

In the event of a fault unplug the heater.

Unplug the heater when not required for long periods.

The supply cord must be placed on the right hand side
of the heater away from the heat outlet underneath the
heater.

Although this heater complies with safety standards, we
do not recommend its use on deep pile carpets or on
long hair type of rugs.

This appliance is not intended for use by children or other
persons without assistance or supervision if their
physical, sensory or mental capabilities prevent them
from using it safely. Children should be supervised to
ensure that they do not play with the appliance.

The appliance must be positioned so that the plug is
accessible.

If the supply cord is damaged it must be replaced by the
manufacturer or service agent or similarly qualified
person in order to avoid a hazard.

Caution: In order to avoid a hazard due to inadvertent
resetting of the thermal cut-out, this appliance must not
be supplied through an external switching device, such
as a timer, or connected to a circuit that is regularly
switched on and off by the utility.

Electrical

WARNING – THIS APPLIANCE MUST BE EARTHED

This heater must be used on an AC ~ supply only and the voltage
marked on the heater must correspond to the supply voltage.
Do not switch the appliance on until properly installed.  Please
read all the safety warnings and operating instructions.

General

Unpack the heater carefully and retain the packaging for
possible future use, in the event of moving or returning the fire
to your supplier.

Contents of Carton.

Heater.

Wall fixing bracket.

Fixing screws and wall plugs.

Remote control and batteries ( 2 AAA’s type).

Spare bulb.

Do not connect the heater to an electricity supply until it is
installed on a wall correctly. - see ‘Installation’.
A choice of 1kW or 2kW heat output is provided by the fan
heater, which is concealed underneath the unit.

S7 - E700FIRE

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

The heater can be used remotely or manually. - see ‘Operation’.
General features of remote control are:

Heat output can be increased or decreased according
to your particular requirements.

The illumination of fuel effect can be increased or
decreased.

Please note: Used in an environment where background noise
is very low, it may be possible to hear a sound which is related
to the operation of the flame effect. This is normal and should
not be a cause for concern.

Installation

Do not connect appliance until properly fixed to the wall
and the Instruction leaflet is read fully.
The minimum distances must be observed.

For installation of the appliance, care must be taken not to
damage concealed cables.
Please be careful while drilling the holes.
This model is designed to be permanently fixed to a wall at a
minimum height of 300mm.
The wall bracket must be fitted horizontally and the cable routed
to the bottom right of the heater as in 

Fig. 1

.

A height of 600mm from bottom of heater to floor is recommended
for optimum viewing of fuel bed (see 

Fig. 2

 for recommended

fixing dimensions).
For optimum viewing mark the top two screw fixing positions on
wall in accordance with the recommended fixing dimensions -
see 

Fig. 2

.

Fix the wall bracket using the two plugs and screws provided -
see 

Fig. 3

.

Carefully lift the heater up ensuring that the top rear ledge of
heater engages the wall bracket and is sitting centrally positioned
- see 

Fig. 4 

(b).

Rotate the bottom fixing bracket down - see 

Fig 4.

 (c).

Gently bring the heater level with the wall - see 

Fig 4.

 (d).

Mark the bottom hole position (see 

Fig. 5

), remove the heater

ensuring that the bottom fixing bracket is rotated up.
Drill and fit wall plug.
Refit the heater to the wall fixing bracket (i.e. follow steps as in

Fig. 4

 a, b, c and d above) and rotate the bottom fixing bracket

down again and use the screw provided to permanently fix the
heater in place.
The heater should not be connected until the instruction leaflet
is read fully.
Note: Fix the appliance to the wall using the screws and wall
plugs provided, but these fixings do not suit all types of walls.
IT IS IMPORTANT THAT THE FIXING DEVICE CHOSEN IS
APPROPRIATE TO THE WALL MATERIAL TO WHICH THE FIRE
IS BEING FIXED. SOME MODERN INTERNAL BUILDING
MATERIALS ARE VERY LOW DENSITY BLOCK AND REQUIRE
SPECIALIZED FIXING DEVICES TO PROVIDE A SAFE,SECURE
INSTALLATION.

Manual & Remote Operation

Setting

Operation

Setting

Flame Effect

Bottom Neon

Flame Effect & 1Kw Heat            Press the ‘ 

’ button

Middle Neon

Flame Effect & 2Kw Heat             Press the ‘ 

’ button again

Top Neon

Summary of Contents for S7 - E700FIRE









Reviews: