background image

Before cleaning or maintenance,
switch off the electricity supply.

Replacing a light bulb

1. Switch off the electricity supply.
2. Remove the grease filters from the

hood.

3. Unscrew the bulb from the holder.

Replacement  bulbs  can  be
obtained  from  your  supplier  or
local hardware store.

4. Fit  the  new  bulb,  ensuring  it  is

screwed securely into the holder.

5. Refit the grease filters.

To  avoid  any  fire  risk,  the  following
cleaning instructions must be followed:

Grease filters

The grease filters absorb grease and
dust from cooking fumes, which would
otherwise damage the inside of the hood.  
The  grease  filter  should  be  removed
and  cleaned  regularly  -  with  normal
use, this should be every 2 months.

I m p o r t a n t :

Frequent  washing  is

essential  to  prevent  a  build  up  of
grease  in  the  filters  which  could
become a fire hazard.
1. Remove the filters from the hood.
2. Carefully wash the grease filters in

hot  soapy  water  and  dry  with  a
clean towel.

3. Refit the clean filters.

Outer casing

All external parts of the outer casing
and visor can be safely cleaned with a
clean  cloth  wrung  out  in  hot  soapy
water.

Do  not  use

caustic  pastes,  abrasive

cleaning  powders,  wire  wool  and
hard implements, as they will damage
the surfaces.

Carbon filters

(models installed for

use with the re-circulation method only)

The  carbon  filters  absorb  cooking
odours and need renewing after about
4  months  of  normal  use.   A  replace-
ment  carbon  filter  can  be  obtained
from your supplier.
Saturation of the activated charcoal in
the filter will depend on how often the
hood is used, the type of kitchen and
the regularity of cleaning the grease filter.

The  carbon  filters  cannot  be
washed - renew every 4 months.

1. Remove the grease filters from the

hood.

2. Release  the  old  carbon  filters  by

twisting them in either direction by
a  quarter  turn  (90˚)  until  they
disengage.

3. Fit  the  new  carbon  filters  by

engaging  them  onto  the  pegs  in
the  centre  of  the  fan  grille  and
twisting by a quarter turn until they
are gripped securely.

4. Refit the grease filters.

5

Care & Maintenance

08 27123 01- 1100TRC hood  17/5/05  4:14 pm  Page 7

Summary of Contents for 1100TRC

















Reviews: