background image

EQUIPMENT WARRANTY: 

 

 

In lieu of all other warranties, express or implied, we warrant the equipment covered by 

Stout Designs LLC to be free from defects in material and workmanship under normal use and 

service and when  properly maintained.  Use or service with corrosive or abrasive chemicals or 

cutting materials larger than the 2” diameter recommendation shall not be deemed normal.  Our 

obligation  under  this  warranty  is  limited  to  repairing  or  replacing  any  part  or  correcting  any 

workmanship which shall be demonstrated to our satisfaction to have been defective at time of 

assembly and with respect to which a written claim specifying the particular defect or defects shall 

have been delivered to us within one (1) year from and after acceptance by you, or before the 

machine has had 100 hours of running use, whichever period is shorter.  Defective parts shall be 

returned to us F.O.B. our factory and repaired or replacement parts shall shipped by us F.O.B. our 

factory.  The removal by you of parts returned to us for repair or replacement and the installation 

by you of replacement or repaired parts shall be at your expense.  We do not warrant equipment 

manufactured by others, but will submit to you upon request the manufacturer's warranty and 

consider this warranty a pass through warranty.  We neither assume, nor authorize any other person 

to assume for us any other liability in connection with the equipment covered by this proposal on 

its installation or erection, including, without limiting the generality of the foregoing, liability or 

loss of production, product, equipment or profits and liability for consequential damages or any 

damage to persons or property.  We will make no allowances for repairs, alterations or other work 

done unless specifically agreed to in writing.  In no event shall we be liable for any compensatory 

or consequential damage in connection with the installation, use or failure of the equipment. 

Currently, Honda GC160 Engines have a noncommercial use term of 2 years.  Commercial use 

term of 3 months.  GX series Honda or Kohler engines are available that carry 3 year warranty for 

an additional charge.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for TB-001








































Reviews: