6600 Lumen LED
Weatherproof 4 ft.
Ceiling Light
MODEL No: WWL4-6600N
PACKAGE CONTENTS
INSTALLATION (CONTINUED)
ADDITIONAL WARNINGS
3 YEAR LIMITED WARRANTY
This product is guaranteed against failure due to factory defects in materials or workmanship for three (3) years from the date of
purchase. This warranty is non-transferable and applies only to the original owner. Proof of purchase is required for repair or
replacement. This warranty does not cover normal wear of parts or damage resulting from any misuse of the product. Misuse of
the product includes, but is not limited to: washing the product, using in extreme weather conditions, opening the product, or
trying to remodel the product. Important: this warranty is only valid if the product has been purchased through an authorized
reseller.
WARNINGS
WARNING: Do NOT look directly at LED light sources.
This fixture is IP66 rated and therefore is suitable for wet
location indoor /outdoor use.
WARNING: Use only in 100-277VAC, 60Hz circuits.
WARNING: TO AVOID ELECTRIC SHOCK,
DISCONNECT POWER BEFORE INSTALLING
SAFETY AND PRECAUTIONS
1. Suitable for indoor/outdoor use.
2. Do NOT install over stoves.
3. Do NOT look directly at LED light sources.
4. The LED modules used in this fixture are not serviceable.
5. This product is inspected prior to shipping. Do not use if product is cracked, broken or missing parts.
6. Suitable for use in operating environments ranging between -4° to 122°F (-20° to 50° C).
7. Electrical requirements can be found on back of the fixture.
8. If unsure how to install a light fixture, call a qualified electrician.
• Shut off power to electrical outlet before installing or servicing this fixture.
CUSTOMER SERVICE
For questions regarding this product, please contact us at 303.652.6164, M-F 7am - 4pm MT or e-mail us at
[email protected].
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment. The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or
relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a
circuit different from that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help.
Electrical requirements can be found on fixture.
Use with a minimum 90° C supply conductors.
Revision Date: 09-20-2017
TROUBLESHOOTING GUIDE
CLEANING INSTRUCTIONS
Disconnect power to fixture before cleaning. Using a soft cloth, clean the fixture using a mild, non-abrasive glass cleaner. DO
NOT use solvents. DO NOT use cleaners containing abrasive agents. NEVER spray liquid cleaner directly onto the LEDs, fixture
or wiring.
Before starting work to connect the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.
1.69 in.
4,3 cm
WARNING: DO NOT alter or disassemble the fixture it is
completely enclosed and does not contain replaceable or
serviceable parts.
DIMMING
• DO NOT USE THIS FIXTURE WITH DIMMERS.
Doing so will void the warranty of this product.
Product Facts:
Color Temperature: 4000K
Lumens: 6600 LM
Lumen Efficacy: 143
Input Voltage: AC120/60Hz
Rated Watts: 46W
CRI: 80
Power Factor: 0.9
LED Beam Angle: 120°
LED Emitter Life: 50,000 hours
Operating Voltage: 100-277v
Operating Temperature: -4° to 122°F (-20° to 50° C)
Cord: 18/2 SJT
Cord Length:1.5 ft
1
4
3
2
3. Move the fixture up to the mounting
clips (Fig. 10). Hook one side of the
mounting track to both mounting clips
(Fig. 11) and push the fixture up (Fig.
12) until the mounting clip track snaps
into the mounting clips (Fig. 13).
48 in.
122 cm
CAUTION: Personal injury can occur, along with damage
to the fixture and/or mounting surface may result if the
fixture is pulled from the surface. To prevent premature failure
from overheating, fixture should only be installed in
environments where the operating temperatures are between
-4° to 122°F (-20° to 50° C).
WARNING: This product may represent a possible shock or
fire hazard if improperly installed or mounted. Products should
be installed following these instructions, local electrical codes and/or
the current National Electric Code (NEC).
Fig. 11
Fig. 12
Fig. 13
Fig. 6
2.9 in.
7,3 cm
WARNING: DO NOT install lights within 10 feet of a pool,
spa or fountain.
WARNING: This product needs to be grounded properly in a
manner consistent with local electrical codes and/or the
current National Electric Code (NEC). If the installer cannot
determine if this product is properly grounded, has no ground wire,
or is unfamiliar with electrical wiring methods of properly
grounding fixture, consult a qualified electrician.
WARNING: Avoid using this product in the immediate vicinity of
highly flammable materials, liquids and gases.
INSTALLATION INSTRUCTIONS
2x Medium
Screws
2x Mounting
Clips
2x Wall
Anchors
INSTALLATION (CONTINUED)
Fixture does not turn on.
Problem
Probable Cause
Solution
Circuit breaker trips or fuse blows
when light is turned on.
1. Bad connection.
2. Faulty switch.
3. Power is off.
1. Discontinue use
immediately.
1. Check wiring connections.
2. Test switch or replace it.
3. Verify power supply is on.
1. Call customer service at 303.652.6164.
2. Call an electrician.
BACK
SIDE
Mounting Clip Track
16” Insulated
Direct Wire Cord
Diffuser
1. Each mounting clip attaches approximately 4 inches from each end of the fixture on the mounting clip track (Fig. 2). Locate where
each mounting clip will be mounted and mark the location on the mounting surface (Fig. 3).
Fig. 2
Fig. 3
Drywall installation:
With a 3/16 in. drill bit, drill holes
for both anchors (included) at the
marked installation locations (Fig.
5). Insert each anchor into the
pre-drilled holes (Fig. 6). Fasten
the mounting clips into place
with the included screws (Fig. 7).
Snap light into clips.
Wood Surface Mount:
Using a 1/8 in. drill bit, drill pilot
holes for both screws (included)
at the predetermined installation
location (Fig. 8). Fasten the
mounting clips into place with
the included screws (Fig. 9).
Snap light into clips.
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
2. Mounting Clips can be mounted to wood or drywall.
4”
4”
Before beginning, disconnect the power to the junction box. If replacing an existing fixture with more than two wire
leads, make a note as to where they were connected.
Fig. 1
1. Disconnect the power to the junction box. Attach the direct wire
cord to a junction box, use wire nuts to connect the black wire
from the direct wire cord to the black power supply wire (Live)
from the junction box and the white wire from the direct wire cord
to the white power supply wire (Neutral) from the junction box
(Fig. 1). After making the connections, carefully push the excess wiring
inside the junction box.
3. Your installation is now complete (Fig. 14). Restore the power.
Fig. 14
