22 in. Linkable LED
Mini Full Spectrum
Grow Strip Light
MODEL No:
#GR-ST2
PACKAGE CONTENTS
INSTALLATION INSTRUCTIONS
VELCRO MOUNT
CLIP MOUNT
LINKING (OPTIONAL)
ADDITIONAL WARNINGS
5 YEAR LIMITED WARRANTY
This product is guaranteed against failure due to factory defects in materials or workmanship for five (5) years from the date of purchase.
This warranty is non-transferable and applies only to the original owner. Proof of purchase is required for repair or replacement. This
warranty does not cover normal wear of parts or damage resulting from any misuse of the product. Misuse of the product includes, but is
not limited to: washing the product, using in extreme weather conditions, opening the product, or trying to remodel the product. Important:
this warranty is only valid if the product has been purchased through an authorized reseller.
WARNING:
Do
NOT
look directly at LED light sources.
This fixture is
rated for dry
location indoor use only.
WARNING:
Use only in 120VAC, 60Hz circuits.
WARNING:
To prevent cord damage, do not expose
cords to edges of sheet metal or other sharp objects.
SAFETY AND PRECAUTIONS
1. Suitable for indoor dry locations only.
2. Do
NOT
install over stoves, sinks or aquariums.
3. Do
NOT
look directly at LED light sources.
4. The LED modules used in this fixture are not serviceable.
5. This product is inspected prior to shipping.
Do not use if product is cracked, broken or missing parts.
6. Suitable for use in operating environments ranging between -4° to 113°F (-20° to 45° C).
6. Do
NOT
install this light inside of enclosed cabinets.
7. Do
NOT
use in wet locations.
8.
Turn power off prior to servicing fixture.
9. Do
NOT
leave bare wires exposed outside of the electrical connections.
10. Electrical requirements can be found on back of the fixture.
11. If unsure how to install a light fixture, call a qualified electrician.
• Never install this fixture while plug in to a power source.
CUSTOMER SERVICE
For questions regarding this product, please e-mail us at
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user’s authority to operate the equipment. The user is cautioned that any changes or modifications not
expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and
receiver. 3) Connect the equipment into an outlet on a circuit different from that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help.
TROUBLESHOOTING GUIDE
CLEANING INSTRUCTIONS
Disconnect power to fixture before cleaning. Using a soft cloth, clean the fixture using a mild, non-abrasive glass cleaner. DO NOT use
solvents. DO NOT use cleaners containing abrasive agents. NEVER spray liquid cleaner directly onto the LEDs, fixture or wiring.
Before starting work to connect the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.
Fixture does not turn on.
Problem
Probable Cause
Solution
Circuit breaker trips or fuse blows
when light is turned on.
1. Bad connection.
2. Faulty switch.
3. Power is off.
1. Discontinue use
immediately.
1. Check wiring connections.
2. Test switch or replace it.
3. Verify power supply is on.
1. Email customer service at
.
2. Call an electrician.
1.38 in.
3,5 cm
0.87 in.
2,2 cm
CAUTION:
Personal injury can occur, along with damage to the
fixture and/or mounting surface may result if the fixture is
pulled from the surface. To prevent premature failure from over-
heating, fixture should only be installed in environments where the
operating temperatures are between -4° to 113°F (-20° to 45° C).
Do not install in a totally enclosed (no ventilation) area.
WARNING: TO AVOID ELECTRIC SHOCK,
DISCONNECT POWER BEFORE INSTALLING
WARNING:
This product may represent a possible shock or
fire hazard if improperly installed or mounted. Products should be
installed following these instructions, local electrical codes and/or the
current National Electric Code (NEC).
WARNING:
DO NOT alter or disassemble the fixture, it is completely
enclosed and does not contain replaceable or serviceable parts.
DIMMING
1
4
3
2
1. Determine where and how the light will be mounted. Mount with either the included metal clips or with velcro strips.
48 in.
122 cm
1. An additional linking cord is included that will allow additional lights to be controlled by a single switch (
Fig. 11)
. The linking
cords allow a
MAXIMUM
of 180 Watts (Models GR-ST2 and GR-ST1) using a single power source to be connected together.
2. Lights can also be linked together directly without using the linking cord (
Fig. 12)
.
WARNINGS
• DO NOT USE THIS FIXTURE WITH DIMMERS.
Doing so will void the warranty of this product.
LED Facts:
FRPF (700-800nm): 1.58
PPF (400-700nm): 13.4
Blue PF (400-500nm): 2.11
Red PF (600-700nm): 7.67
LED Life: 50,000 hours
Operating Voltage: 120v
Cord Type: .SPT-2/35 IN.
Revision Date: 07-02-2020
LINKING CORD
LINKING CORD
1. Determine whether to link multiple units together with either a linking cord or through direct linking.
2x
Medium
Screws
2x Mounting
Clips
1x
Contact plug
1x
12” linking
cord
1x
35 in.
power cord
On/off switch
Power cord
contact pins
Linking
connector
2x Velcro
Mounting
Strips Sets
2x
Wall
Anchors
1. Wipe the light down with a dry cloth. DO NOT
separate the 2 sides of the velcro strips . Remove the
liner on one side of the velcro strips (
Fig. 1)
. Press 1
each of the strips down firmly on the back side of the
fixture approximately 1-1/2” to 2” in from each end
and 1 centered (in the gray areas) as shown.
Remove the liner from the top side of both pairs of
strips (
Fig. 2)
. Press the fixture firmly into place. Hold
in place for 30 seconds.
Drywall installation:
Using a 1/8” drill bit, drill holes for the
three (3) wall anchors (included) at the
predetermined installation location
(
Fig. 3)
. Insert anchors into the
pre-drilled holes (
Fig. 4)
. Fasten the
clips into place with the included
screws (
Fig. 5)
. Snap light into clips.
Wood Surface Mount:
1. Using a 3/16” drill bit, drill pilot holes
for the three (3) screws (included) at
the predetermined installation location
(
Fig. 6)
. Fasten the clips into place
with the included screws (
Fig. 7)
. Snap
light into clips.
2. Firmly push the light into the clips
(
Fig. 8)
. Apply pressure until light
snaps into clips (
Fig. 9)
.
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
2. Plug in the direct wire cord to the fixture
(
Fig. 10)
. Restore power to the electrical box.
Fig. 11
Fig. 12
1-
1
/
2
” - 2”
