background image

17

866-795-1586 • WWW.STONEAGETOOLS.COM

TERMS AND CONDITIONS AND WARRANTY INFORMATION

8. Disputes.

  Seller and Buyer shall attempt in good 

faith to promptly resolve any dispute arising under 
these Terms and Conditions by negotiations between 
representatives who have authority to settle the 

controversy.  If unsuccessful, Seller and Buyer shall 

further attempt in good faith to settle the dispute 
by nonbinding third-party mediation, with fees and 

expenses of such mediation apportioned equally to 
each side.  Any dispute not so resolved by negotiation 
or mediation may then be submitted to a court of 
competent jurisdiction in accordance with the terms 

hereof.  These procedures are the exclusive procedures 
for the resolution of all such disputes between the Seller 

and Buyer.

9. 

Governing Law.

  All sales, agreements for sale, offers 

to sell, proposals, acknowledgments and contracts 

of sale, including, but not limited to, purchase orders 
accepted by Seller, shall be considered a contract under 

the laws of the State of Colorado and the rights and 

duties of all persons, and the construction and effect of 
all provisions hereof shall be governed by and construed 
according to the laws of such state.

10. 

Jurisdiction and Venue. 

 Seller and Buyer agree 

that the state or federal courts located within the City 

and County of Denver, Colorado shall have sole and 
exclusive jurisdiction over any litigation concerning any 
dispute arising under these Terms and Conditions not 
otherwise resolved pursuant to Section  9 as well as any 
alleged defects of any Products  or damages sustained 
as a result of such alleged defects.  Seller and Buyer 

further agree that should any litigation be commenced 
in connection with such a dispute, it shall only be 

commenced in such courts.  Seller and Buyer agree to 

the exclusive jurisdiction of such courts and neither will 
raise any objection to the jurisdiction and venue of such 

courts, including as a result of inconvenience. 

11. 

Attorney’s Fees.

  If any litigation is commenced 

between Seller and Buyer, or their personal 
representatives, concerning any provision hereof, 
the party prevailing in the litigation shall be entitled, 
in addition to such other relief that is granted, to a 
reasonable sum as and for their attorneys’ fees and 

costs in such litigation or mediation.

STONEAGE TRADEMARK LIST  
View the list of StoneAge’s trademarks and service marks and learn how the trademarks should be used. Use of 
StoneAge trademarks may be prohibited, unless expressly authorized. 

http://www.StoneAgetools.com/trademark-list/ 

STONEAGE PATENT DATA  
View the list of StoneAge’s current U.S. patent numbers and descriptions.

http://www.sapatents.com

STONEAGE TERMS AND WARRANTY 
View StoneAge’s Terms and Warranty Conditions online.

http://www.stoneagetools.com/terms
http://www.stoneagetools.com/warranty

Summary of Contents for SPINCAT SC-125





















Reviews: