background image

-  7  -

Technical Data

Machine Sound & Vibration Mea-

surements/Lubrication Specs

Lubrication Spe cifications

Re comme nde d Fue l

Gasoline 86 Octane minimum

Engine  Oil

Mobil Delvac 1200 10W30, approximately

1.3 quarts/1.2 liters

(check engine manual)

Ge ar Cas e

Mobilube HD80W-90 API GL-5
40 ounces/1.2 liters

Gre as e  Fittings

Mobilegrease XHP222

(NLGI 2EP Lithium Complex)

Sound and Vibration Measurements

Sound Pressure Values as measured are per the following:

Noise 1

Model/Configuration

Sound Pressure

CF364

5.5 Honda

CF464

8 Honda

CF484

11 Honda

at operator’s ear

92dBA

93dBA

93dBA

RMS acceleration on the handle were measured per the following:

meter/sec

2  RMS

8.27

1.5

Sound and vibration values have been taken in accordance to the EEC machine regulation
(edition 93/68/EEC)
Sound Pressure measurements were taken with Simpson model 886-2 type 2 meter, calibrated
1/31/98
1/17/2003
Acceleration measurements were taken with Quest Tech model VI-100 meter, calibrated 4/17/96
1/17/2003
Sound and vibration measurements were obtained with machine operating at maximum engine
speed of 3600 RPM.
Unit measurements were taken on steel test plate.

Summary of Contents for CF24E

























Reviews: