background image

Notes on Safety

ID 441806.03

4

Commissioning Instructions Bottom brake resistor

1

WE KEEP THINGS MOVING

Tab. 1-1: examples of occupational qualifications

In addition, the valid regulations, the legal requirements, the reference books, this technical documentation 
and, in particular, the safety information contained therein must be carefully

read

understood and

complied with

1.4

Installation and connection

Installation and connection work are only permitted after the device has been isolated from the power!
The accessory installation instructions allow the following actions during the installation of accessories:

The housing in the upper slot can be opened

The housing in the bottom slot can be opened.

Opening the housing in another place or for other purposes is not permitted.
The accessory installation instructions allow the following actions during the installation of accessories:

The housing in the upper slot can be opened.

Opening the housing in another place or for other purposes is not permitted.

Use only copper lines. For the line cross sections to be used, refer to DIN VDE 0298-4 or DIN EN 60204-1 
Appendix D and Appendix G.
Protect the device from falling parts (pieces of wire, leads, metal parts, and so on) during installation or other 
tasks in the switching cabinet. Parts with conductive properties inside the inverter can cause short circuits or 
device failure.
The motor must have an integrated temperature monitor with basic isolation in acc. with EN 61800-5-1 or 
external motor overload protection must be used.
The permissible protection class is protective ground. Operation is not permitted unless the protective 
conductor is connected in accordance with the regulations. 
Comply with the applicable instructions for installation and commissioning of motor and brakes.

Commissioning 

 

(of a standard application)

- Technician (m/f) (electro-technology)
- Master electro technician (m/f)

Programming

Graduate engineer (electro-technology or 
electrical power technology)

Operation

- Technician (m/f) (electro-technology)
- Master electro technician (m/f)

Disposal

Electronics technician (m/f)

Activity

Possible occupational qualifications

Summary of Contents for RB 5022















Reviews: