manualshive.com logo in svg

STMicroelectronics STM32F405, Reference Manual

The STMicroelectronics STM32F405 is a powerful microcontroller featuring a Cortex-M4 core, ideal for embedded applications. To get the most out of this product, make sure to download the free Reference Manual from manualshive.com. The manual provides detailed information on how to maximize the STM32F405's capabilities.

Share
Download
background image

Flexible static memory controller (FSMC)

RM0090

1554/1731

DocID018909 Rev 11

Figure 446. Multiplexed write accesses

The difference with mode D is the drive of the lower address byte(s) on the databus.

          

Table 235. FSMC_BCRx bit fields 

Bit No.

Bit name

Value to set

31-21

Reserved

0x000

19

CBURSTRW

0x0 (no effect on asynchronous mode)

18:16

CPSIZE

0x0 (no effect on asynchronous mode)

15

ASYNCWAIT

Set to 1 if the memory supports this feature. Otherwise keep at 
0.

14 EXTMOD

0x0

13

WAITEN

0x0 (no effect on asynchronous mode)

12

WREN

As needed

11

WAITCFG

Don’t care 

10

WRAPMOD

0x0

9 

WAITPOL 

Meaningful only if bit 15 is 1

8 BURSTEN

0x0 

7 Reserved

0x1

6 FACCEN

0x1

5-4 MWID 

As 

needed

3-2 

MTYP[0:1] 

0x2 (NOR Flash memory)

A[25:16]

NOE

ADD

S

ET (DATA

S

T + 1)

Memory tr

a

n

sa

ction

NEx

AD[15:0]

HCLK cycle

s

 HCLK cycle

s

NWE

NADV

d

a

t

a

 driven by F

S

MC

a

i15569

1HCLK

ADDHLD
HCLK cycle

s

Lower 

a

ddre

ss

Summary of Contents for STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for STM32F405

unicore UM960 Installation And Operation User Manual preview
UM960
Brand: unicore Pages: 25
unicore UM960L Installation And Operation User Manual preview
UM960L
Brand: unicore Pages: 24
Eaton XN300 Manual preview
XN300
Brand: Eaton Pages: 288
Fanimation BTCR9 Quick Start Manual preview
BTCR9
Brand: Fanimation Pages: 2
M2M C600 Technical Manual preview
C600
Brand: M2M Pages: 24
Maguire Products GRAVIMETRIC AUGER FEEDER MGF-ST Instruction Manual preview
GRAVIMETRIC AUGER FEEDER MGF-ST
Brand: Maguire Products Pages: 47
Magtrol DSP7000 User Manual preview
DSP7000
Brand: Magtrol Pages: 160
Ziton ZP1-X3E Series Operation Manual preview
ZP1-X3E Series
Brand: Ziton Pages: 36
PUTCO 8770HF Installation preview
8770HF
Brand: PUTCO Pages: 2
Data Signs PTL Compact 2 Operation And Maintenance Manual preview
PTL Compact 2
Brand: Data Signs Pages: 23
Procom DGC-6D Operating Instructions Manual preview
DGC-6D
Brand: Procom Pages: 10
LOGICDATA DYNAMIC MOTION Configuration Handbook preview
DYNAMIC MOTION
Brand: LOGICDATA Pages: 23
Cypress CY8C28 series Technical Reference Manual preview
CY8C28 series
Brand: Cypress Pages: 571
Conductrix Wampfler 0832 Installation Instructions Manual preview
0832
Brand: Conductrix Wampfler Pages: 23
Carel E2V Installation preview
E2V
Brand: Carel Pages: 2
Timotion TBB5 User Manual preview
TBB5
Brand: Timotion Pages: 9
END ARMATUREN DF3D Original Operating Manual preview
DF3D
Brand: END ARMATUREN Pages: 32
Nice HSCU1 Instructions And Warnings For Installation And Use preview
HSCU1
Brand: Nice Pages: 40

Brands by name

Popular brands

Load more brands