STMicroelectronics SPEAr300 Reference Manual Download Page 626 | Manualshive

Page: 626 / 844

background image

LS_I2C controller

RM0082

Doc ID 018672 Rev 1

28.6.8 IC_SS_SCL_HCNT register (0x014)

The IC_SS_SCL_HCNT is a 16 bit RW register which allows setting the high period of the
SCL clock for standard-speed mode. The IC_SS_SCL_HCNT bit assignments are given in

Note:

1

This register can be written only when the I

2

C controller is disabled, which corresponds to

the IC_ENABLE (

Section 28.6.21

) register being set to ‘b0. Write at other times has no

effect.

2

This register must be set before any I

2

C bus transaction can take place in order to ensure

proper I/O timing.

[08]

CMD

RW

1‘h0

Control read or write.

This bit controls whether a read or write is
performed, according to the encoding:

1‘b0 = Write.

1‘b1 = Read.

Note: In case of reading, the lower bits
from 7 to 0 (DAT field) are ignored by the
I

2

C controller. Reading this bit returns 'b0.

Attempting to perform a read operation
after a general call command has been
sent results in TX_ABRT unless the
SPECIAL bit in IC_TAR register (see

Section 28.6.4

) has been cleared. If this bit

is written to ‘b1 after receiving RD_REQ,
then a TX_ABRT occurs.

[07:00]

DAT

RW

7‘h0

Contains data.

This 8 bit field contains the data to be
transmitted or received on the I

2

C bus.

Read these bits means reading out the
data received on the I

2

C interface. Write

this field means sending data out on the
I

2

C interface.

Table 546.

IC_DATA_CMD register bit assignments (continued)

Bit

Name

Type

Reset
value

Description

Table 547.

IC_SS_SCL_HCNT register bit assignments

Bit

Name

Type

Reset
value

Description

[15:00]

IC_SS_SCL_HCNT

RW

16'h29B

SCL clock high period count for standard
speed.

This 16 bit field states the SCL clock high
period count for standard speed. The
minimum valid value is 6, and hardware
prevents that a value less than this minimum
will be written (setting 6 if attempted)

«
...
624
625
626
627
628
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Brand: Facility Explorer Pages: 4

Brand: DayTronic Pages: 22

Brand: HANYOUNG NUX Pages: 36

Brand: HANYOUNG NUX Pages: 4

Brand: MADRIX Pages: 91

Brand: MADRIX Pages: 40

Brand: YASKAWA Pages: 18

Brand: Daikin Pages: 46

Brand: Daikin Pages: 26

Brand: Swagelok Pages: 16

Brand: S&C Pages: 12

Brand: AUMA Pages: 48

Brand: Jebao Pages: 4

SmartLoop KTSL-FC1-UV-KO

Brand: Keystone Pages: 2

Brand: Hanna Instruments Pages: 28

CompleteStat CS9B-THOA

Brand: Bard Pages: 10

Brand: Nibe Pages: 48

Brand: Air Torque Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands