STMicroelectronics SPEAr300 Reference Manual Download Page 635 | Manualshive

Page: 635 / 844

background image

RM0082

LS_I2C controller

Doc ID 018672 Rev 1

28.6.20 Interrupt

clearing registers(0x044 - 0x068)

With the aim to clear an individual interrupt (among those supported by the I

2

C controller,

and listed in

), a specific RO register must be read, according to below:

Note:

RX_FULL and TX_EMPTY interrupts have no a specific clearing register, because they are
automatically cleared by hardware when buffer level goes below/above the threshold,
respectively.

28.6.21 IC_ENABLE

register(0x06C)

The IC_ENABLE is a RW register which allow enabling/disabling the I

2

C controller. The

IC_ENABLE bit assignments are given in

Table 564.

IC_CLR_INTR register bit assignments

Bit

Name

Type

Reset
value

Description

[15:01]

Reserved

-

Read: undefined.

[00]

CLR_INTR

RO

1’h0

Reading this register causes interrupt to be
cleared.

Table 565.

Interrupt clearing registers

Register to be read

Relevant interrupt to be cleared (

Section 28.5

)

IC_CLR_RX_UNDER

RX_UNDER

IC_CLR_RX_OVER

RX_OVER

IC_CLR_TX_OVER

TX_OVER

IC_CLR_RD_REQ

RD_REQ

IC_CLR_TX_ABRT

TX_ABRT

IC_CLR_RX_DONE

RX_DONE

IC_CLR_ACTIVITY

ACTIVITY

IC_CLR_STOP_DET

STOP_DET

IC_CLR_START_DET

START_DET

IC_CLR_GEN_CALL

GEN_CALL

«
...
633
634
635
636
637
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Leroy-Somer R180

Brand: Nidec Pages: 20

Brand: Gardena Pages: 18

VLT Micro Drive FC 51 Series

Brand: Danfoss Pages: 23

Brand: RadioMaster Pages: 49

Brand: FASAR ELETTRONICA Pages: 2

Brand: ACTi Pages: 20

Brand: SOARNEX Pages: 14

Brand: HANYOUNG NUX Pages: 4

Brand: Levven Pages: 2

Brand: R-Tec Pages: 14

SWD Starter Kit

Brand: ez-wheel Pages: 30

Brand: ICStation Pages: 3

Brand: Monde Synthesizer Pages: 4

Brand: Kathrein Pages: 116

DD-1920-DUAL-DVI

Brand: Digital View Pages: 30

Brand: Norgren Pages: 2

ProfiLux Garden LED Controller

Brand: Oase Pages: 116

SUPERTRAK TX8650

Brand: Promise Technology Pages: 191

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands