background image

6

29. With the seatback in the up position set the subwoofer in place 
against the back of the seatback.  Release the seatback and while 
holding the top of the subwoofer against the seatback slowly rotate the 
seatback forward until the subwoofer bracket slides under the anchor 
point on the seatback.  Continue to hold the subwoofer against the seat 
while rotating the seatback rearward until it locks into the fully back 
position.  Fig. 13
30. Hold fi rm pressure against the bottom of the subwoofer while pulling 
the poly bag from beneath it. 
31. Reinstall all previously removed parts in reverse order.
32. Install fuses into fuse holder. The fuse holder labeled RHCJY3110BP 
uses a 25 amp fuse.  The fuse holder labeled RHCJY3091BP uses a 15 
amp fuse.  
33. Reconnect negative battery cable to battery. Torque to 9 +/- 1.5 Nm

Troubleshooting the Kicker Integrated Systems

If you experience a problem once the Subwoofer is installed use this guide to locate the trouble.

The radio is working, but the Subwoofer is not working:

•  Check the battery voltage to make sure it is not discharged below 11 volts.
•  Check the negative battery cable to see if it has been securely tightened back on the battery.
•  Check the inline fuse located near the battery to make sure it is plugged in completely, and not blown.
•  Check the 12Volt power-connector near the fi rewall to make sure it is plugged in securely.
•  Check the inline connectors near the subwoofer enclosure to make sure they are plugged securely.
•  Check the ground wire connection to make sure it is tightly secured to the proper ground in the vehicle.
•  Check the audio input signal connection to make sure it is secure and connected to the proper wiring.
•  Test with different music in case there is no low frequency audio in the initial sound check.

There is a buzz or rattle noise that accompanies the low frequency element of the music:

•  Check for a connector or any other object that could be very near the enclosure.
•  Check the subwoofer enclosure mounting brackets to make sure they are secure.

There is a problem with the multi-channel stereo amplifi er:

•  Check the battery voltage to make sure it is not discharged below 11 volts.
•  Check the negative battery cable to see if it has been securely tightened back on the battery.
•  Check the inline fuse located near the battery to see if it is plugged in completely and not blown.
•  Check the multi-pin connectors at the back of the radio and at the amplifi er chassis to make sure they are 
plugged all the way in.
•  Check the ground wire connection to make sure it is tightly secured to the proper ground in the vehicle.

If you continue to experience problems after troubleshooting, please contact KICKER Technical Support at (800) 
256-0808 ext. 6009, or 

[email protected]

. Place your warranty card in the glove box for future use, and the 

hang-tag on your mirror.

 

Hatchback installation shown 

Fig. 13 

Summary of Contents for KICKER 19119147









Reviews: