background image

SP 451, SP 481

English

3

quality parts and accessories in order to 
avoid the risk of accidents and damage 
to the machine.

STIHL recommends the use of original 
STIHL replacement parts. They are 
specifically designed to match your 
model and meet your performance 
requirements.

Never attempt to modify your power tool 
in any way since this may increase the 
risk of personal injury.  STIHL excludes 
all liability for personal injury and 
damage to property caused while using 
unauthorized attachments.

Do not use a pressure washer to clean 
the unit. The solid jet of water may 
damage parts of the unit.

Clothing and Equipment

Wear proper protective clothing and 
equipment.

Avoid clothing that could get caught on 
branches or brush or moving parts of the 
machine. Do not wear a scarf, necktie or 
jewelry. Tie up and confine long hair 
(e.g. with a hair net, cap, hard hat, etc.).

Warning! 

A face shield alone does not 

provide adequate eye protection.

Wear hearing protection, e.g. earplugs 
or ear muffs.

Transporting the Power Tool

Always stop the engine.

Carry the unit suspended from the 
harness.

Transporting in a vehicle: Properly 
secure your power tool to prevent 
turnover, fuel spillage and damage.

Fueling

Always shut off the engine before 
refueling.

Do not fuel a hot engine – 

fuel may spill 

and cause a fire

.

Open the fuel cap carefully to allow any 
pressure build-up in the tank to release 
slowly and avoid fuel spillage.

Fuel your power tool only in well-
ventilated areas. If you spill fuel, wipe 
the machine immediately – if fuel gets on 
your clothing, change immediately.

This reduces the risk of unit vibrations 
causing the fuel cap to loosen or come 
off and spill quantities of fuel.

Check for leakage. To reduce the 

risk of 

serious of fatal burn injuries

, do not 

start or run the engine until leak is fixed.

Before starting

Check that your power tool is properly 
assembled and in good condition – refer 
to appropriate chapters in the instruction 
manual.

Clothing must be sturdy 
but allow complete free-
dom of movement. Wear 
snug-fitting clothing, an 
overall and jacket combi-
nation, do not wear a 
work coat.

Wear steel-toed safety 
boots with non-slip soles.

Wear a safety hard hat 
where there is a danger 
of head injuries from fall-
ing objects. Wear a face 
shield and safety 
glasses.

Wear heavy-duty gloves, 
preferably made of 
leather.

4902BA001 KN

Gasoline is an 
extremely flammable 
fuel.

 Keep clear of naked 

flames. Do not spill any 
fuel – do not smoke.

After fueling, tighten 
down the screw-type fuel 
cap as securely as 
possible.

Summary of Contents for SP 451

































Reviews: