EN
85
0478 131 8365 C - EN
– Replace the battery – observe
corresponding recommendation on the
display (
#
), (
– Switch on offset drive home (passage)
Fault:
Unmown grass at edge of mowing area
Possible cause:
– Edge mowing switched off
– Perimeter wire routed inaccurately
– Grass is out of reach of mowing blade
Remedy:
– Mow the edge once or twice per week
– Check routing of the perimeter wire
11.13), check clearances using the
iMOW® Ruler (
– Cut the unmown areas regularly using a
suitable grass trimmer
Fault:
No wire signal
Possible cause:
– Docking station switched off – LED
does not illuminate
– Docking station not connected to mains
supply – LED does not illuminate
– Perimeter wire not connected to
docking station – red LED flashes
(
– Break in perimeter wire – red LED
– Robotic mower and docking station are
not linked
– Electronics fault – LED flashes SOS
Remedy:
– Check power supply to docking station
– Connect perimeter wire to docking
perimeter wire using wire connectors
(
– Link robotic mower and docking station
– Contact your specialist dealer (
#
)
Fault:
LED on the docking station flashes SOS
Possible cause:
– Minimum perimeter wire length not
reached
– Electronics fault
Remedy:
– Install AKM 100 (
#
)
– Contact your specialist dealer (
#
)
Fault:
The robotic mower is not receiving any
GPS signal
Possible cause:
– Connection to satellites is currently
being established
– 3 or fewer satellites within range
– Machine is in a dead spot
Remedy:
– No further action required; it can take a
few minutes for connection to be
established
– Avoid or remove obstacles that might
be blocking signal (e.g. trees, canopies)
Fault:
The robotic mower cannot establish a
mobile radio connection
Possible cause:
– Mowing area is in a dead spot
– Radio module is not activated
Remedy:
– Have radio module checked by a STIHL
specialist dealer (
#
)
Fault:
The robotic mower cannot be reached
using the app
Possible cause:
– Radio module inactive
– Robotic mower is in standby mode
– No Internet connection
– Robotic mower is not associated with
correct e-mail address
Remedy:
– The radio module is switched off during
linking, then it is reactivated and the
robotic mower can be reached again
– Activate robotic mower by pressing
button, set "Standard" energy mode
(
– Connect machine on which app is
installed to Internet
Fault:
Internal mapping for direct drive home
cannot be created
Possible cause:
– Edge following interrupted or aborted,
e.g. by an obstacle, machine being
lifted
– Incorrect wire routing
– Robotic mower leaving perimeter wire
Remedy:
– Repeat edge following, edge following
must be carried out without interruption
– Carry out edge following at a later time
– Correct wire routing
Summary of Contents for RMI 522 C
