background image

MS 311, MS 391

English

34

Install spur chain sprocket / rim 
sprocket

N

Clean crankshaft stub and needle 
cage and lubricate with STIHL 
lubricant (special accessory)

N

Slide needle cage onto the 
crankshaft stub

N

After refitting, turn the clutch drum 
and/or spur chain sprocket approx. 
1 full turn so that the carrier for the 
oil pump drive engages

N

Refit the rim sprocket – cavities 
toward the outside

N

Refit washer and E-clip on the 
crankshaft

Sawing effortlessly with a properly 
sharpened saw chain

A properly sharpened saw chain cuts 
through wood effortlessly even with very 
little pushing.

Never use a dull or damaged saw chain 
– this leads to increased physical strain, 
increased vibration load, unsatisfactory 
cutting results and increased wear.

N

Clean the saw chain

N

Check the saw chain for cracks and 
damaged rivets.

N

Replace damaged or worn chain 
components and adapt these parts 
to the remaining parts in terms of 
shape and level of wear – rework 
accordingly.

Carbide-tipped (Duro) saw chains are 
especially wear-resistant. For an optimal 
sharpening result, STIHL recommends 
STIHL servicing dealers.

The chain pitch marking (

a

) is embossed 

in the area of the depth gauge of each 
cutter.

Use only special saw chain files!

 

Other files are unsuitable in terms of 
shape and type of cutting.

The diameter of file to be used depends 
on the chain pitch – see table 
"Sharpening tools"

The angles of the cutter must be 
maintained during resharpening.

A

Sharpening angle

B

Side plate angle

Maintaining and 
Sharpening the Saw Chain

Compliance with the angles and 
dimensions listed below is 
absolutely necessary. An 
improperly sharpened saw chain – 
especially depth gauges that are 
too low – can lead to increased 
kickback tendency of the chain 
saw – 

risk of injury

!

Marking (

a

)

Chain pitch

Inches

mm

1/4 or 1

1/4

6.35

P, PM or 6

3/8 P

9.32

325 or 2

0.325

8.25

3/8 or 3

3/8

9.32

404 or 4

0.404

10.26

689BA027 KN

a

A

B

689BA021 KN

Summary of Contents for MS 391





































































Reviews: