background image

19.6

Noise and Vibration Data

19.6.1

with KombiTool

For version see "Approved KombiTools".
For further details on compliance with Vibration

Directive 2002/44/EC visit www.stihl.com/vib.
Noise and vibration data measurements include

idling and rated maximum speed in the following

ratios.
FCB‑KM, FCS‑KM, FH‑KM, FS‑KM,

RG-KM and HT‑KM

1 to 1

HL‑KM

1 to 4

BF‑KM, BG‑KM, KB‑KM and

KW‑KM

1 to 6

The exact noise and vibration specifications

depend on the KombiTool being used and are

described in the KombiTool’s instruction manual.
19.6.2

Sound pressure level L

p

 to

EN ISO 10517, ISO 11201, ISO 22868

KM 111 R:

92 dB(A) ... 99 dB(A)

KM 131:

94 dB(A) ... 100 dB(A)

KM 131 R:

92 dB(A) ... 101 dB(A)

19.6.3

Sound power level L

w

 to ISO 3744,

ISO 10517, ISO 22868

KM 111 R:

108 dB(A)

KM 131:

109 dB(A) ... 110 dB(A)

KM 131 R:

109 dB(A) ... 110 dB(A)

19.6.4

Sound power level L

w

 to ISO 3744,

ISO 10517, ISO 22868

KM 111 R:

105 dB(A) ... 110 dB(A)

KM 131:

106 dB(A) ... 108 dB(A)

KM 131 R:

106 dB(A) ... 110 dB(A)

19.6.5

Vibration measurement a

hv,eq

 to

ISO 8662, ISO 10517, ISO 11789,

ISO 20643, ISO 22867

Left handle

KM 111 R:

2.6 m/s

2

 ... 7.2 m/s

2

KM 131:

2.3 m/s

2

 ... 5.0 m/s

2

KM 131 R:

3.4 m/s

2

 ... 6.1 m/s

2

Right handle

KM 111 R:

2.7 m/s

2

 ... 6.4 m/s

2

KM 131:

2.4 m/s

2

 ... 4.2 m/s

2

KM 131 R:

3.3 m/s

2

 ... 6.5 m/s

2

The K‑factor in accordance with Directive

2006/42/EC is 2.0 dB(A) for the sound pressure

level and sound power level; the K‑factor in

accordance with Directive 2006/42/EC is
2.0 m/s

2

 for the vibration level.

19.7

REACH

REACH is an EC regulation and stands for the

Registration, Evaluation, Authorisation and

Restriction of Chemical substances.
For information on compliance with the REACH

regulation (EC) No. 1907/2006 see

www.stihl.com/reach.

19.8

Exhaust Emissions

The CO

2

value measured in the EU type approval

procedure is specified at www.stihl.com/co2.
The measured CO

2

value was determined on a

representative engine in accordance with a

standardized test procedure under laboratory

conditions and does not represent either an

explicit or implied guarantee of the performance

of a specific engine.
The applicable exhaust emission requirements

are fulfilled by the intended usage and mainte‐

nance described in this instruction manual. The

type approval expires if the engine is modified in

any way.

20 Maintenance and Repairs

Users of this machine may only carry out the

maintenance and service work described in this

user manual. All other repairs must be carried

out by a servicing dealer.
STIHL recommends that you have servicing and

repair work carried out exclusively by an author‐

ized STIHL servicing dealer. STIHL dealers are

regularly given the opportunity to attend training

courses and are supplied with the necessary

technical information.
When repairing the machine, only use replace‐

ment parts which have been approved by STIHL

for this power tool or are technically identical.

Only use high-quality replacement parts in order

to avoid the risk of accidents and damage to the

machine.
STIHL recommends the use of original STIHL

replacement parts.
Original STIHL parts can be identified by the

STIHL part number, the 

{

 logo and the

STIHL parts symbol 

K

 (the symbol may appear

alone on small parts).

21 Disposal

Observe all country-specific waste disposal rules

and regulations.

English

20 Maintenance and Repairs

20

0458-436-0121-B

Summary of Contents for KM 111 R

























Reviews: