Stihl FR 460 TC-M Instruction Manual Download Page 21

Page: 21 / 48

FR 460 TC-M

English

WARNING

Wear protective gloves to reduce the

risk of direct contact with the sharp

cutting edges.
Mount only one metal cutting

attachment.
Check direction of rotation of cutting

attachment

Cutting attachments 1, 2, 3 and 4 may

be mounted either way round – they

must be turned over regularly to help

avoid one-sided wear.
The cutting edges of the grass cutting

blades 5 and 6 must point clockwise.

WARNING

Direction of rotation is indicated by an

arrow on the inside of the deflector.

Place the cutting attachment (6) on

the thrust plate (7).

WARNING

Collar (see arrow) must engage the

cutting attachment's mounting hole.
Securing the cutting attachment

Fit the thrust washer (8) – convex

side must face up.

Fit the rider plate (9).

Block the shaft (10).

Use the combination wrench (12) to

screw the mounting nut (11) on to

the output shaft counterclockwise

and tighten it down firmly.

WARNING

If the mounting nut has become too

loose, fit a new one.

NOTICE

Remove the tool used to block the shaft.

Removing the Metal Cutting Attachment

WARNING

Wear protective gloves to reduce the

risk of direct contact with the sharp

cutting edges.

Block the shaft.

Unscrew the mounting nut

clockwise.

Remove cutting attachment and its

mounting hardware from the

gearbox – but do not remove the

thrust plate (7).

681BA312 KN

Summary of Contents for FR 460 TC-M

















































Search results

Summary of Contents for FR 460 TC-M

Reviews:

Related manuals for FR 460 TC-M

Brands by name

Popular brands

Stihl FR 460 TC-M, Instruction Manual

Search results

Summary of Contents for FR 460 TC-M

Reviews:

Related manuals for FR 460 TC-M

Brands by name

Popular brands