background image

3

FC 110

English / USA

Warning!

Because an edger is a 
high-speed, fast-cutting 
power tool, special safety 
precautions must be 

observed to reduce the risk of personal 
injury.

It is important that you 
read, fully understand and 
observe the following 
safety precautions and 
warnings. Save this 
owner's manual and read 

the safety instructions periodically. Be 
thoroughly familiar with the controls and 
the proper use of the equipment. Know 
how to stop the unit and disengage the 
controls quickly.
Careless or improper use of any edger 
may cause serious or fatal injury.

Have your STIHL dealer show you how 
to operate your edger. Observe all 
applicable local safety regulations, 
standards and ordinances.

!

Warning!

The use of any edger may be 
hazardous. If the rotating cutting tool 
comes in contact with your body, it will 
cut you. When it comes in contact with 
solid foreign objects such as rocks or 
bits of metal, it may fling them directly or 
by ricochet in the direction of bystanders 
or the operator.

Striking such objects could damage the 
cutting attachment and may cause 
blades to crack, chip or break. Thrown 
objects or damaged blades may result in 
serious or fatal injury to the operator or 
bystanders.

!

Warning!

Minors should never be allowed to use 
an edger. Bystanders, especially child-
ren and animals should not be allowed in 
the area where an edger is in use.

Never let the edger run unattended.

!

Warning!

Do not lend or rent your edger without 
the owner's manual. Be sure that any-
one using your edger understands the 
information contained in this manual.

Most of these safety precautions and 
warnings apply to the use of all STIHL 
edgers. Different models may have 
different parts and controls. See the 
appropriate section of your owner's 
manual for a description of the controls 
and function of the parts of your model 
edger.

Safe use of an edger involves

1. the operator
2. the edger
3. the use of the edger.

Save these instruction !

THE OPERATOR!

Physical Condition

You must be in good physical condition 
and mental health and not under the 
influence of any substance (drugs, 
alcohol, etc.) which might impair vision, 
dexterity or judgment. Do not operate an 
edger when you are fatigued.

Be alert - if you get tired while operating 
your edger, take a break. 
Tiredness may result in loss of control. 
Working with any edger can be 
strenuous. If you have any condition that 
might be aggravated by strenuous work, 
check with your doctor before operating 
an edger.

Safety Precautions

Summary of Contents for FC 110





















Reviews: