background image

10

English

Cut-off-Machine Safety Manual

!

Warning!

Use of this product to cut masonry, 
concrete, metal and other materials can 
generate dust and fumes containing 
chemicals known to cause serious or 
fatal injury or illness, such as respiratory 
disease, cancer, birth defects or other 
reproductive harm. If you are unfamiliar 
with the risks associated with the 
particular material being cut, review the 
material safety data sheet and/or consult 
your employer, the material 
manufacturer/supplier, governmental 
agencies such as OSHA and NIOSH 
and other sources on hazardous 
materials. California and some other 
authorities, for instance, have published 
lists of substances known to cause 
cancer, reproductive toxicity, etc. Control 
dust and fumes at the source where 
possible. In this regard use good work 
practices and follow the 
recommendations of the manufacturer/
supplier, OSHA/NIOSH, and 
occupational and trade associations. A 
water attachment kit is provided with 
your cut-off machine and should be used 
for dust suppression when wet cutting is 
feasible. If wet cutting is not utilized, the 
operator and any bystanders should 
always wear a respirator approved by 
NIOSH/MSHA for the material being cut. 
Consult and follow any federal, state or 
local laws or regulations with respect to 
dry and wet cutting.

!

Warning!

Cutting masonry, concrete and other 
materials with silica in their composition 
may give off dust containing crystalline 
silica. Silica is a basic component of 
sand, quartz, brick clay, granite and 
numerous other minerals and rocks. 
Repeated and/or substantial inhalation 
of airborne crystalline silica can cause 
serious or fatal respiratory diseases, 
including silicosis. In addition, California 
and some other authorities have listed 
respirable crystalline silica as a sub-
stance known to cause cancer. When 
cutting such materials, always follow the 
respiratory precautions mentioned 
above. 

!

Warning!

Breathing asbestos dust is dangerous 
and can cause severe or fatal injury, 
respiratory illness or cancer. The use 
and disposal of asbestos-containing 
products have been strictly regulated by 
OSHA and the Environmental Protection 
Agency. Do not use your cut-off machine 
to cut or disturb asbestos, asbestos-
containing products, or products such as 
pipes which are wrapped or covered 
with asbestos insulation. If you have any 
reason to believe that you might be 
cutting asbestos, immediately contact 
your employer or a local OSHA 
representative.

!

Warning!

Your STIHL cut-off machine is designed 
for hand-held use or operation on a cut-
off machine cart. Cutting with your cut-
off machine resting on the ground or 
other surface can cause excessive wear 
to the bracket designed to protect the 
bottom of the tank housing. Loss of fuel 
and personal injury from fire may result. 
Replace damaged or badly worn 
brackets immediately.

Grip: Never use the cut-off machine with 
one hand. Always hold the cut-off 
machine firmly with both hands when the 
engine is running. Place your left hand 
on front handle bar and your right hand 
on rear handle and throttle trigger. Left-
handed users should follow this 
instruction too.

002BA060 KN

Summary of Contents for Cutquik TS 700































Reviews: