background image

Edition

Manual

Chapter

Page

2008-05-19 Workshop Manual, Stiga Park

1 General instructions

13

1.5 Service

Every new machine is delivered with a service book. This service book is part of the active 
post-market programme and shall be kept in a safe place during the entire lifetime of the 
machine. Hand over the service book if the machine is sold in 2:nd hand.

Service should generally be carried out at least every 50 operating hours (exception of the 
first service), although in accordance with the conditions below.

There are three different grades of service events. Every service event consists of a 
number of service points as described in the following paragraphs. Every service point has 
a number which refer to a describing text after the schedules.

Some service points do not coincide with the scheduled service intervals, but shall be 
performed in connection with a scheduled service when possible. E.g. some items shall be 
performed at every second service and some also between two services. These service 
points are described with procedure and interval in the respective “Instruction for use”.

Typical service points wich not coincide with scheduled service intervals are:
• Cleaning/changing air filter in some motors.
• Change of oil in some motors.
• Valve adjustments for some motors.
• Change of transmission oil in 4 WD machines.
• Change of spark plug in some motors.

Summary of Contents for Park 2/4WD





















Reviews: