Stiga BC 536, Operator'S Manual

Page: 35 / 50

EN - 10
IMPORTANT The machine
is supplied without fuel.
6.1 PRELIMINARY OPERATIONS
Before using the machine:
1. place the machine in a stable
horizontal position on the ground;
2. choose the most suitable cutting means
for the job to be done (par. 4.3);
3. fill up with fuel. For information
about how to prepare the fuel blend,
methods and precautions for refuelling,
see sections 7.2 and 7.3;
4. wear the harness correctly
(see section 6.1.1).
6.1.1 Using the harness
The straps must be adjusted in accordance
with the height and build of the operator.
• Models with double strap
The harness must be worn before securing
the machine to the attachment.
The strap (Fig. 15.A) must be worn with:
– the support (Fig. 15.A.1), the machine's
carabiner hook (Fig.15.A.2). and the quick
release hook (Fig. 15.A.3) on the right side.
– the quick release at the front (Fig. 15.A.4);
– the strap crossover on the back
of the operator (Fig. 15.A.6);
– the buckles correctly fastened (Fig. 15.A.5).
The straps must be tightened so that they
distribute the load evenly over the shoulders.
IMPORTANT In case of danger, unhook the
machine using the quick release (Fig. 15.A.3).
• Models with back-pack harness
Harness with back-pack must be
worn after starting the machine.
The harness (Fig. 15.B) must be worn with:
– the harness straps on the operator’s
shoulders (Fig. 15.B.1);
– the buckles properly fastened (Fig. 15.B.2).
– the snap-hook coupling on the
right side (Fig. 15.B.3);
– the quick release in front (Fig. 15.B.4).
The belts must be tensioned so that the load
is evenly distributed on the shoulders.
IMPORTANT In case of danger, unhook the
harness using the quick release (Fig. 15.B.4).
6.2 SAFETY CHECKS
Run the following safety checks and
ensure that the results correspond
to those outlined in the tables.
Always carry out the safety
checks before use.
6.2.1 General check
Object Result
Grips (Fig. 1.F, Fig.
1.G, Fig. 1.I)
Clean, dry and fixed
firmly to the machine.
Cutting means
guard: (Fig. 1.E)
Suitable for the cutting
means used, correctly
and securely attached to
the machine, not worn/
deteriorated or damaged.
Harness connection
point (Fig. 1.J).
Correctly positioned.
Quick release (Fig.15.A.3,
Fig. 15.B.4)
Efficient. It must allow the
machine to be released
quickly in case of danger.
Screws on the machine
and the cutting means.
Correctly tightened
(not loose)
Cutting means (Fig. 1.D.1,
Fig. 1.D.2, Fig. 1.D.3)
Not damaged or worn
Metal blade (if fitted)
(Fig. 1.D.2, Fig. 1.D.3, )
Well sharpened.
Air filter (Fig. 24.C) Clean
Electrical cables and
spark plug cable.
In good condition to
avoid causing sparks.
Spark plug cap (Fig. 14 .H) In good condition
and correctly fitted
on the spark plug
6.2.2 Machine operating test
Action Result
Start the machine
(section 6.3 );
The cutting means (Fig.
1.D.1, Fig. 1.D.2, Fig.
1.D.3) must not move
when the engine is idling.
Simultaneously activate
the throttle control lever
(Fig. 14.B) and throttle
safety lever (Fig. 14.C) .
They must be able
to move freely
without forcing.
Release the throttle
control lever (Fig. 14.B)
and the throttle safety
lever (Fig. 14.C)
The levers must return
automatically and quickly
to the neutral position
and the engine must
return to idle speed.
Press the accelerator
control lever (Fig. 14.B)
The throttle lever remains
locked (Fig. 14 .B) .