background image

operATIoN 

 

General information

14

 | WSH 10 | WSH 20 

www.stiebel-eltron.com

operATIoN

1.  General information

The chapters „Special information“ and „Operation“ are intended 

for both users and qualified contractors.
The chapter „Installation“ is intended for qualified contractors.

 

Note

Read these instructions carefully before using the appli-

ance and retain them for future reference.

Pass on the instructions to a new user if required.

1.1  Safety instructions

1.1.1  Structure of safety instructions

 

KEYWORD Type of risk

Here, possible consequences are listed that may result 

from failure to observe the safety instructions.

f

f

Steps to prevent the risk are listed.

1.1.2  Symbols, type of risk

Symbol

Type of risk

 

 

Injury 

 

 

 

Electrocution 

 

 

 

Burns

(burns, scalding) 

1.1.3  Keywords

KeYword

Meaning

DANGER 

Failure to observe this information will result in serious 

injury or death.

WARNING 

Failure to observe this information may result in serious 

injury or death.

CAUTION 

Failure to observe this information may result in non-seri-

ous or minor injury.

1.2  Other symbols in this documentation

 

Note

General information is identified by the adjacent symbol.

f

f

Read these texts carefully.

Symbol

Meaning

 

 

Material losses

(appliance damage, consequential losses and environmen-

tal pollution)

 

 

Appliance disposal 

 

f

f

This symbol indicates that you have to do something. The ac-

tion you need to take is described step by step.

1.3  Units of measurement

 

Note

All measurements are given in mm unless stated oth-

erwise.

2.  Safety

2.1  Intended use

The sensor tap is suitable for connection to pressurised (sealed 

unvented) DHW appliances.
Any other use beyond that described shall be deemed inappro-

priate. Observation of these instructions and of the instructions 

for any accessories used is also part of the correct use of this 

appliance.

2.2  General safety instructions

 

CAUTION Burns

During operation, the sensor tap can reach temperatures 

in excess of 60 °C.

There is a risk of scalding at outlet temperatures in ex-

cess of 43 °C.

 

WARNING Injury

The appliance may be used by children over 8 years of 

age and persons with reduced physical, sensory or men-

tal capabilities or a lack of experience and expertise, 

provided that they are supervised or they have been 

instructed on how to use the appliance safely and have 

understood the potential risks. Children must never play 

with the appliance. Children must never clean the ap-

pliance or perform user maintenance unless they are 

supervised.

Summary of Contents for WSH 10













Reviews: