manualshive.com logo in svg

Stid ultrys, User Manual

Share
Download
Stid ultrys User Manual Download Page 179

 

179 

 

SPECTRE ATX READ ONLY  

© STid 

–

 MU_ULTRYS_V3.0.1_EN 

Advanced settings  

  

 

 

Adjust the antenna power (10% to 100%) to adjust the reading distance. 

 

The power emitted depends on the type of regulation, limited to 1800mw ERP for ETSI and 
1200mw ERP for FCC, New Zealand and Australia. No limitation for Morocco. 

 

 

 

Adjust the timing for a scan (reading) by step of 1 second (max 30s). 
This setting is taking into account only if 

Input type selection

 is set to 

Activating all lanes

 or 

Activating the event lane.

 

 

 

 

The EPC filter is not available in Secure Mode

.  

Enter the value for EPC Mask, max 62 hexadecimal bytes. 

 

 

 

Adjust the value for offset EPC mask in bytes (0 to 62). It depends on the EPC Mask length. 

 

 

 

Filter inversion

 

not selected: only tags with an EPC value corresponding to the EPC mask value 

will be provided to the user.  

Filter inversion selected: only tags with an EPC value different from the EPC mask value will be 
provided to the user. 

 

 

 

RSSI (Received Signal Strength Indication) is a measure of the power in reception of the tag 

response. The value returned by the reader is proportional to the amplitude of the reception 

signal Adjust the RSSI value (-110dBm to 0dBm). 0dBm deactivates the RSSI filter. 

 

 

 

Filter inversion

 

not selected: only tags with an RSSI greater than or equal to the specified value 

will be provided to the user. 

Filter inversion

 

selected: only tags with an RSSI smaller or equal to the specified value will be 

provided to the user. 

 

Ex: RSSI filter = -49f=dBm + Reversal not selected 
      A tag that will have a RSSI value of -20dBm will be sent back, 

      A tag that will have a RSSI value of -60dBm will not be sent back. 

2 

 a 

b  

c 

d

e

f 

b

 

c 

d 

e

f

g 

g 

a 

Summary of Contents for ultrys










































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands