— 7 —
Enrolling Sensors into Mirror Receiver Systems (with or
without latching):
When using a mirror RECEIVER system, the latching feature is set independently on the master and/or mirror RECEIVERS.
Latching on the master and/or mirrored RECEIVERS is only set for a zone at the time the SENSOR is enrolled into the master
RECEIVER. You will need to set (SW2 ON) and (SW3 ON or OFF) for each RECEIVER at the time of SENSOR enrollment.
1. Check that each RECEIVER is not in DELETE mode (SW7 OFF).
2. Set desired “latching” on each system RECEIVER. A RECEIVER set to (SW3 ON) will have latching. The RECEIVER set to (SW3
OFF) will only indicate the zone status.
3. Set each RECEIVER to ENROLL mode, (SW2 ON), that will store the latch setting.
4. Check that the zone flashing GREEN on the master RECEIVER is correct, and note the zone(s) with RED LEDs.
5. Trigger an alert on the SENSOR being enrolled and return it to the restored state (if restore is triggered manually).
6. The RECEIVER will give a double beep and the zone LED will change to continuous RED.
7. Repeat steps 2-6 to enroll another SENSOR.
8. To exit ENROLL mode, set (SW2 OFF) on the master RECEIVER.
9. Set all master and/or mirror RECEIVERS (SW3 OFF).
System Examples
DELETING SINGLE ZONES (Sensors and Keyfobs):
1. Enter DELETE mode (SW7 ON). All enrolled zone LEDs will turn RED. The first zone to be deleted will have the LED
flashing RED.
2. Press and release the push button to cycle the flashing LED through the zones until it reaches the zone to be deleted.
3. Press and hold the push button for 5 seconds to delete the zone with the flashing LED. The RECEIVER will give a single
beep and the LED will turn off. Release the push button.
DELETING ALL ZONES (Sensors, Mirrored Receivers and Keyfobs):
You must delete all zones in order to delete keyfobs and/or a mirrored RECEIVER.
1. Enter DELETE mode (SW7 ON). All enrolled zone LEDs will turn RED. The first zone to be deleted will have the LED
flashing RED.
2. Press and hold the push button for 5 seconds. The RECEIVER will give a single beep and the flashing LED will turn off.
Continue to hold the push button.
3. After the first zone is deleted and while still holding the push button, all other enrolled zones will flash for 5 seconds. The
RECEIVER will give a double beep and all of the LEDs will turn off when those zones are deleted.
WIRE ROUTE
OPTION 1
FORM C
SWITCH OUTPUTS
12 VDC INPUTS
TERMINALS 500mA
12 VDC OUTPUTS
TERMINALS 300mA
WIRE ROUTE
OPTION 2
TRIGGERED OUTPUT PLUG
12VDC, 75mA, 3 SEC.
ADAPTER PLUG INPUT
12VDC, 500mA
SURFACE FEET (x4)
(WALL MOUNTING HOLES)
ANTENNAS
SWITCHES 1-8
LEDs
PUSH BUTTON
SPEAKER
FRONT COVER
SCREW
19018 ANCHOR
(4) PROVIDED
MARK AND DRILL
3/16 DIAMETER HOLES
(4) PLACES
19108 NYLON WASHER
(4) PROVIDED
19039 SCREW
(4) PROVIDED
PUSH BUTTON
19081 FRONT COVER SCREW
PUSH BUTTON SWITCH
Represents any STI 433 MHz sensor transmitting ONLY to a Master Receiver
SYSTEM 1
SYSTEM 2
MULTLIPLE SYSTEMS
Master
Receiver
Mirror #1
Receiver
Mirror #2
Receiver
Up to
1000 ft
Up to
1000 ft
Up to
1000 ft
Up to
1000 ft
Up to
1000 ft
Up to
1000 ft
Master
Receiver
Mirror #1
Receiver
Master
Receiver
Mirror #1
Receiver
Mirror #2
Receiver
- Last
Mirror #2
Receiver
- Last
Monitors Housed in a
Central Office or Location
SINGLE SYSTEM
Mirror #3
Receiver
Up to
1000 ft
Mirror #4
Receiver
- Last
Up to
1000 ft
EMBOSSED
PROGRAMMING
INSTRUCTIONS
EMBOSSED
INPUT AND
OUTPUTS
Switches (1-8)
- For reference, information is also written on the
receiver case (located under Zone ID list).
1 - MIRROR MASTER OFF/ON
2 - NORMAL/ENROLL
3 - AUTO RESTORE/LATCH
4 - SIREN TIME/MIRROR#
5 - SIREN TIME/MIRROR#
6 - CHIME OFF/ON
7 - NORMAL/DELETE
8 - MIRROR SLAVE OFF/ON
SIREN
SW4
SW5
TIME
MIRROR #
OFF
OFF
DISABLED
1
ON
OFF
30 SEC
2
OFF
ON
180 SEC
3
ON
ON
ON CONT
4
Embossed Programming Instructions:
ZONES:
LEFT BUTTON
“CALL”
RIGHT BUTTON
“RESTORE”
NO ZONE:
ON and OFF
BUTTONS
WIRE ROUTE
OPTION 1
FORM C
SWITCH OUTPUTS
12 VDC INPUTS
TERMINALS 500mA
12 VDC OUTPUTS
TERMINALS 300mA
WIRE ROUTE
OPTION 2
TRIGGERED OUTPUT PLUG
12VDC, 75mA, 3 SEC.
ADAPTER PLUG INPUT
12VDC, 500mA
SURFACE FEET (x4)
(WALL MOUNTING HOLES)
ANTENNAS
SWITCHES 1-8
LEDs
PUSH BUTTON
SPEAKER
FRONT COVER
SCREW
19018 ANCHOR
(4) PROVIDED
MARK AND DRILL
3/16 DIAMETER HOLES
(4) PLACES
19108 NYLON WASHER
(4) PROVIDED
19039 SCREW
(4) PROVIDED
PUSH BUTTON
19081 FRONT COVER SCREW
PUSH BUTTON SWITCH
Represents any STI 433 MHz sensor transmitting ONLY to a Master Receiver
SYSTEM 1
SYSTEM 2
MULTLIPLE SYSTEMS
Master
Receiver
Mirror #1
Receiver
Mirror #2
Receiver
Up to
1000 ft
Up to
1000 ft
Up to
1000 ft
Up to
1000 ft
Up to
1000 ft
Up to
1000 ft
Master
Receiver
Mirror #1
Receiver
Master
Receiver
Mirror #1
Receiver
Mirror #2
Receiver
- Last
Mirror #2
Receiver
- Last
Monitors Housed in a
Central Office or Location
SINGLE SYSTEM
Mirror #3
Receiver
Up to
1000 ft
Mirror #4
Receiver
- Last
Up to
1000 ft
EMBOSSED
PROGRAMMING
INSTRUCTIONS
EMBOSSED
INPUT AND
OUTPUTS
Switches (1-8)
- For reference, information is also written on the
receiver case (located under Zone ID list).
1 - MIRROR MASTER OFF/ON
2 - NORMAL/ENROLL
3 - AUTO RESTORE/LATCH
4 - SIREN TIME/MIRROR#
5 - SIREN TIME/MIRROR#
6 - CHIME OFF/ON
7 - NORMAL/DELETE
8 - MIRROR SLAVE OFF/ON
SIREN
SW4
SW5
TIME
MIRROR #
OFF
OFF
DISABLED
1
ON
OFF
30 SEC
2
OFF
ON
180 SEC
3
ON
ON
ON CONT
4
Embossed Programming Instructions:
ZONES:
LEFT BUTTON
“CALL”
RIGHT BUTTON
“RESTORE”
NO ZONE:
ON and OFF
BUTTONS
