STI PR-7505 Manual Download

Page: 3 / 16

HARDWARE IDENTIFICATION CHART

This chart is provided to help identify the hardware used in the assembly process. Place the washers, the end of the bolts,

or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws.

NOTE:

The length of all bolts and screws except those with flat heads is measured

from below the head to the end of the bolt or screw. Flat head bolts and

screws are measured from the top of the head to the end of the bolt or screw.

After unpacking the unit, open the hardware bag and make sure that you have all the following items. Some hardware

may be already attached to the part.

Part No. and Description

Q’TY

66 Lock Washer (M8)

70 Washer (8x38x2.0t)

80 Screw, Round Head (M5xp0.8x15mm)

81 Screw, Round Head (M5xp0.8x50mm)

83 Bolt, Socket Head (M8xp1.25x10mm)

90 Bolt, Button Head (M10xp1.5x85mm)

94 Bolt, Hex Head (M8xp1.25x65mm)

95 Bolt, Hex Head (M10xp1.5x50mm)

104 Nylock Nut (M10xp1.5)

105 Nut Cap

Summary of Contents for PR-7505

















Search results

Summary of Contents for PR-7505

Reviews:

Related manuals for PR-7505

Brands by name

Popular brands

STI PR-7505, Manual

Search results

Summary of Contents for PR-7505

Reviews:

Related manuals for PR-7505

Brands by name

Popular brands