STI PR-7505 Manual Download

Page: 8 / 16

ASSEMBLE INSTRUCTIONS

STEP 10

CAUTION:

Be careful not to

damage the

Middle Pulse Sensor

Wire (112)

while assembling

STEP

Slide the

Console Bracket (18)

onto

the

Front & Back Upright Cover

(44, 45)

as the

FIG1

illustration

shows on the top left corner.

STEP 11

NOTE:

For shipping purpose, the

Bolt, Button Head

(M8xp1.25x12mm) (87)

and

Lock

Washer (M8) (66)

are attached on

the

Upright Post (4).

a. Remove the

Bolt, Button Head (M8xp1.25x12mm) (87)

and

Lock Washer (M8) (66)

from the

Upright

Post (4).

b. Attach the

Console Fixed Bracket (43)

onto the

Upright Post (4)

and secure with the

Bolt, Button Head

(M8xp1.25x12mm) (87)

and

Lock Washer (M8) (66).

STEP 12

NOTE:

For shipping purpose, the

Bolt, Button Head (M8xp1.25x16mm) (88)

and

Lock Washer (M8) (66)

are

attached on the

Stationary Handlebar (5).

a. Remove the

Bolt, Button Head (M8xp1.25x16mm) (88)

and

Lock Washer (M8 ) (66)

from the

Stationary

Handlebar (5).

b. Connect the

Middle Pulse Sensor Wire (112)

and the

Lower Pulse Sensor Wire (113)

to the

Stationary

Handlebar (5).

c. Insert the

Stationary Handlebar (5)

into the

Upright Post (4)

and secure with the

Bolt,

Button Head (M8xp1.25x16mm) (88)

and

Lock Washer (M8) (66).

NOTE:

After connecting the wires

’ pins, slightly and gently pull two sides of wires to test and

make sure whether the wires are fully connected.

Summary of Contents for PR-7505

















Search results

Summary of Contents for PR-7505

Reviews:

Related manuals for PR-7505

Brands by name

Popular brands

STI PR-7505, Manual

Search results

Summary of Contents for PR-7505

Reviews:

Related manuals for PR-7505

Brands by name

Popular brands