manualshive.com logo in svg

Stewart MacDonald bomb boost, Assembly Instructions Manual, Page: 9 / 10

Share
Download
Stewart MacDonald bomb boost Assembly Instructions Manual Download Page 9

stewmac.com 

©2017 Stewart-MacDonald 

page 9 of 10

DC power connector

Negative

Positive

JHS Pedals Kit

For Stew Mac

DC Jack

Mini Bomb

C1

C2

Q1

VOLUME

InJ

S
T

S
T

R4
R3

R1
R2

D1

OutJ

P78869

R4

.1J63

D8

Step 11: Install the footswitch

Step 12: Install the DC power connector

JHS Pedals Kit

For Stew Mac

DC Jack

Mini Bomb

C1

C2

Q1

VOLUME

InJ

S
T

S
T

R4
R3

R1
R2

D1

OutJ

P78869

R4

.1J63

D8

Thread one of the nuts onto the 

footswitch

, leaving 

a 1/8" gap between it and the switch housing. Place 
the split lock washer on next. 

Carefully install the switch so the legs of the diode feed through the 

D8

 holes 

on the switch circuit board. 

Place the flat washer on the switch shaft on the top of the case. As you tighten 
the remaining nut on the switch, hold the switch circuit board inside the case 
so that it doesn’t rotate. 

Solder the 

D8

 LED and trim the leads.

1/8"

Insert the 

DC power connector 

 so the negative lug is facing up, and tighten 

it in place. The negative lug is the one with the largest metal tab. 

Solder the installed leads from the circuit board to the jack. Where they attach 
to the board, the positive lead is on the the right and the negative is on the left.

This pedal requires a standard 9V DC center-negative power supply (not 
included) and consumes less than 100mA.

Summary of Contents for bomb boost











Reviews:

No comments