manualshive.com logo in svg

Stewart MacDonald bomb boost, Assembly Instructions Manual, Page: 3 / 10

Share
Download
Stewart MacDonald bomb boost Assembly Instructions Manual Download Page 3

stewmac.com 

©2017 Stewart-MacDonald 

page 3 of 10

Parts list

Resistor values are indicated by colored bands, read from left 
to right. The first color in the code is usually the one painted 
closest to a lead wire. When a gold or silver band is present, 
it’s always one of the last colors in the code. A magnifier is 
a big help in reading these codes.

#7422 (1) 

D8

 Clear LED (5mm)

#7431 (1) LED mounting bezel (5mm)

#7481 (1) 

Q1

 Transistor (J201)

#7318 (1) Ribbon cable (2")

(6)  Lead wires (2")

#7460 (1) DC power connector (21MM)

#1611 (1) Footswitch (3PDT, latching)

#7360 (1) 

R1

 Resistor (5.1 kΩ)

#7365 (1) 

R2

 Resistor (100 kΩ)

#7351 (1) 

R3

 Resistor (47 Ω)

#7357 (1) 

R4

 Resistor (1 kΩ)

#7402 (1) 

D1

 Diode (P6KE12A)

#7311 (1) 

C1

 Capacitor (22 µF)

#7560 (4) Adhesive foam tape

#7456 (1) Volume pot (1 MΩ, linear taper)

#4652 (2) Mono jacks, 1/4"

#7551 (1) Metal case with 4 screws

(1) Circuit board

#7501 (1) Control knob

(Not pictured)

(Not pictured)

Green Brown Black Brown Brown

Brown Black Black Orange Brown

Yellow Purple Black

Gold Brown

Brown Black Black Brown Brown

22uF

#7304 (1) 

C2

 Capacitor (.1 µF)

.1J63

Summary of Contents for bomb boost











Reviews:

No comments