manualshive.com logo in svg

Stewart MacDonald bomb boost, Assembly Instructions Manual, Page: 7 / 10

Share
Download
Stewart MacDonald bomb boost Assembly Instructions Manual Download Page 7

stewmac.com 

©2017 Stewart-MacDonald 

page 7 of 10

Step 7: Install the lead wires, cut the board

Step 8: Install the LED mounting bezel and the two jacks

Cut the 

lead wire

 into six 2" lengths for the input, output, and power jacks. 

Strip the insulation on the ends and thread them through the front of the 
board. Solder them on the back of the board.

Now you can cut the switch portion of the board away from the main board. 
Small wire cutters make quick work of this, and a small saw also works.

LED mounting bezel

Two jacks

Install the plastic 

mounting bezel

 for the LED indicator by pressing it in 

from the outside, through the top of the case. Spread the tabs open inside 
the case to hold it in place.

Install the 

input and output jacks

 on the sides of the case. Keep the lugs 

facing up so you’ll have easy access when it’s time to solder them.

JHS Pedals Kit

For Stew Mac

DC Jack

Mini Bomb

C1

C2

Q1

VOLUME

InJ

S
T

S
T

R4
R3

R1
R2

D1

OutJ

P78869

D8

.1J63

Lead wire, cut into six 2" lengths

Summary of Contents for bomb boost











Reviews:

No comments