Stephill SSD10000 Handbook Download Page 4

Issue 3 
 

Page 2 

18/06/2015 

2  General Safety 
 
2.1 Warning signs 

Warnings  shown  on  the  machine  should  be  observed  at  all  times.  The  warning  signs 
should be checked for legibility and any that have become damaged should be replaced. 
The following are shown on the generator: 
 

 
2.2 Safety hazards 

Do not climb on the generator, as dents may cause overheating of the acoustic lining. It is 
important to keep the generator clean and well serviced, in particular keep all air vents / 
louvers  clear  of  debris  to  prevent  poor  performance  or  possible  overheating  and 
permanent damage to the generator. 
Keep well clear of moving parts on the generator at all times. 
Children and pets must be kept clear of the operating area. 

 

3 Potential Hazards 
 
3.1 Auxiliary power 

The electricity produced by an engine driven generator is very similar to mains electricity 
and should be treated accordingly. 
Do not remove covers and attempt to work on the generator while the engine is running. 
Check the rating and electrical safety of the load before connecting the generator. 
Equipment  should  never  be  connected  that  in  total  exceeds  the  specified  rating  of  the 
generator. 
Installation  of  the  generator  as  a  standby  or  secondary  power  source  should  only  be 
undertaken  by  a  fully  qualified  electrician  using  the  appropriate  means  of  isolation  from 
the mains supply. Installation must comply with all applicable laws and electrical codes. 

 
3.2 Operating Environment  

The generator should always be operated on level ground. 

 
3.3 Temperature Range 

A temperature range between -15˚C and +45˚C are the normal limits of operation. 
Operating outside the range will require additional modifications. 

 
3.4 Reference Relative Humidity 

The standard reference condition for relative humidity is 30%. Above this value the rated 
power must be reduced. 

 
 

 

 

 

   CAUTION 

 

   HOT EXHAUST

 

 

 

    

        RISK OF ELECTRIC  SHOCK 

                  ALWAYS TURN OFF GENERATOR 
 

        BEFORE OPENING. KEEP 

 

        CLOSED AT ALL OTHER TIMES

 

 
 

 

BEFORE STARTING. 

 

READ HANDBOOK AND SAFETY ADVICE 

 

CHECK OIL LEVEL 

 

DO NOT ADJUST ENGINE SPEED  

  WITHOUT SUITABLE TEST EQUIPMENT 

WARNING 

 

Summary of Contents for SSD10000



















Reviews: