Stellar Hearth Products 3-RD-2-GL Installation And Operating Manual Download Page 18 | Manualshive

Page: 18 / 52

Stellar Hearth Products 3-RD-2-GL Installation And Operating Manual Download Page 18

Page 18

INSTALL_3-RD-GL-R REV A

7 - GLASS FRAME ASSEMBLY

CAUTION: TO PREVENT GLASS FRAME ASSEMBLY FROM FALLING FROM FIREPLACE AND BECOMING DAMAGED, FOLLOW

THE INSTRUCTIONS EXACTLY WHEN REMOVING AND INSTALLING GLASS FRAME ASSEMBLY.

STOP: DO NOT OPERATE THIS FIREPLACE WITH THE GLASS REMOVED, CRACKED OR BROKEN. REPLACEMENT OF GLASS

ASSEMBLY SHOULD BE DONE BY A LICENSED OR QUALIFIED SERVICE PERSON.

WARNING: RISK OF INJURY!

DO NOT remove glass until unit is cooled to room temperature. Glass breakage could occur.

NOTE: GLASS REMOVAL AND INSTALLATION MUST BE PERFORMED WITH TWO PEOPLE.

NOTE: Glass must be removed using quality suction cups.

DO NOT attempt to remove the glass without using proper suction cups.

NOTE: IN CASE OF CHIPPED OR BROKEN GLASS

Have your local dealer assist you with contacting Stellar Hearth Products directly for glass replacement.

«
...
16
17
18
19
20
...
»

Summary of Contents for 3-RD-2-GL





















































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands