Stellar Hearth Products 3-RD-2-GL Installation And Operating Manual Download Page 1

Custom Fireplace Program

Direct Vent Gas Fireplaces 
Installation and Operating Manual

Model: GALAXY ROUND

—  Do not store or use gasoline or other 

flammable vapors and liquids in the 

vicinity of this or any other appliance.

—  WHAT TO DO IF YOU SMELL GAS

  •  Do not try to light any appliance.

  •  Do not touch any electrical switch; 

do not use any phone in your 

building.

  •  Leave the building immediately.

  •  Immediately call your gas supplier 

from a neighbor’s phone. Follow the 

gas supplier’s instructions.

  •  If you cannot reach your gas 

supplier, call the fire department.

—  Installation and service must be 

performed by a qualified installer, 

service agency or the gas supplier.

Stellar Hearth Products

TM

, a brand of Hearth & Home Technologies

®

 -  16873 Fish Point Rd. SE, Prior Lake, MN 55372

WARNING:

FIRE OR EXPLOSION HAZARD.

Failure to follow safety warnings exactly 

could result in serious injury, death, or 

property damage.

 

 

DANGER

HOT GLASS

 WILL 

CAUSE BURNS.

DO NOT TOUCH

 GLASS 

UNTIL COOLED. 

 

NEVER

 ALLOW CHILDREN 

TO TOUCH GLASS

.

IMPORTANT:

This appliance is only for 

use with Natural Gas

Installer:  Leave this manual with the appliance.

Consumer:  Retain this manual for future reference.

Page 1

Summary of Contents for 3-RD-2-GL





















































Reviews: