background image

7

The pressure washer is equipped with a stop device that will sense the trigger on the gun is released. It

will open the power circuit to the motor and cause the pressure washer to stop.

 

 

Warning:  

The pressure washer is also equipped with a main power ON/OFF switch

 

located on the unit. It should always be moved to the off position, when the pressure

 

washer is not being used to prevent possible injury or damage.

 

Motor Overload

 

The electric motor in this pressure washer is equipped with an overload protection device that will

 

automatically shut off the motor in the event the motor draws excessive current or overheats.

 

The device will automatically reset itself and resume normal operation a short period of time.

 

Extension Cords

 

Warning:  

Extension cords are not recommended unless they are plugged into a

 

ground-fault circuit-interrupter found in circuit boxes or protected receptacles.

 

Use only 3-wire extension cords that have 3-prong grounding-type plugs and 3-pole cord connector

 

that accept the plug from the product.

 

Use only extension cords that are intended for outdoor use. These extension cords are identified by a

 

marking “Acceptable for use with outdoor appliances; store indoors while not in use”.

 

Use only extension cords having an electrical rating higher than the rating of the product.

 

Do not use damaged extension cords.

 

Examine extension cord before using and replace if damaged.

 

Do not abuse extension cord and do not yank on any cord disconnect.

 

Keep cord away from heat and sharp edges.

 

Always disconnect the extension cord from the receptacle before disconnecting the product from the

 

extension cord.

 

When using an extension cord, observe the specification below:

 

 

Cable Length   

 

Wire Gauge

 

MIN 35ft  

 

 

16

 

 

Warning:  

To reduce the risk of electrocution keep all connections dry and off the

 

ground. Do not touch plug with wet hands.

Safety Features

Summary of Contents for SP-WE180



















Reviews: